uda1321 NXP Semiconductors, uda1321 Datasheet - Page 42
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
uda1321
Manufacturer Part Number
uda1321
Description
Universal Serial Bus Usb Digital-to-analog Converter Dac
Manufacturer
NXP Semiconductors
Datasheet
1.UDA1321.pdf
(44 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
uda1321H/N101
Manufacturer:
PHILIPS
Quantity:
1 809
Part Number:
uda1321H/N101
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
Part Number:
uda1321T
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
Part Number:
uda1321T/N101
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
Company:
Part Number:
uda1321T/N101Ј¬118
Manufacturer:
NXP
Quantity:
5 985
Part Number:
uda1321T/N1O1
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Philips Semiconductors
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(order code 9398 652 90011).
SDIP
S
The maximum permissible temperature of the solder is
260 C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (T
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
R
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 C, contact may be up to 5 seconds.
QFP and SO
R
Reflow soldering techniques are suitable for all QFP and
SO packages.
The choice of heating method may be influenced by larger
plastic QFP packages (44 leads, or more). If infrared or
vapour phase heating is used and the large packages are
not absolutely dry (less than 0.1% moisture content by
weight), vaporization of the small amount of moisture in
them can cause cracking of the plastic body.
1998 Oct 06
OLDERING BY DIPPING OR BY WAVE
EPAIRING SOLDERED JOINTS
EFLOW SOLDERING
Universal Serial Bus (USB)
Digital-to-Analog Converter (DAC)
stg max
). If the
42
For details, refer to the Drypack information in the
“Data Handbook IC26; Integrated Circuit Packages;
Section: Packing Methods” .
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
infrared/convection heating in a conveyor type oven.
Throughput times (preheating, soldering and cooling) vary
between 50 and 300 seconds depending on heating
method. Typical reflow peak temperatures range from
215 to 250 C.
W
QFP
Wave soldering is not recommended for QFP packages.
This is because of the likelihood of solder bridging due to
closely-spaced leads and the possibility of incomplete
solder penetration in multi-lead devices.
If wave soldering cannot be avoided, for QFP
packages with a pitch (e) larger than 0.5 mm, the
following conditions must be observed:
SO
Wave soldering techniques can be used for all SO
packages if the following conditions are observed:
Wave soldering is NOT applicable for all QFP
packages with a pitch (e) equal or less than 0.5 mm.
AVE SOLDERING
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave)
soldering technique should be used.
The footprint must be at an angle of 45 to the board
direction and must incorporate solder thieves
downstream and at the side corners.
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
The longitudinal axis of the package footprint must be
parallel to the solder flow.
The package footprint must incorporate solder thieves at
the downstream end.
CAUTION
Preliminary specification
UDA1321