nbc12430 ON Semiconductor, nbc12430 Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
nbc12430
Manufacturer Part Number
nbc12430
Description
3.3v/5vprogrammable Pll Synthesized Clock Generator
Manufacturer
ON Semiconductor
Datasheet
1.NBC12430.pdf
(20 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
nbc12430AFA
Manufacturer:
ON Semiconductor
Quantity:
10 000
Company:
Part Number:
nbc12430AFAG
Manufacturer:
ON Semiconductor
Quantity:
249
Company:
Part Number:
nbc12430AFAG
Manufacturer:
ON Semiconductor
Quantity:
10 000
Company:
Part Number:
nbc12430AFAR2
Manufacturer:
ON Semiconductor
Quantity:
10 000
Company:
Part Number:
nbc12430AFAR2G
Manufacturer:
ON Semiconductor
Quantity:
10 000
Part Number:
nbc12430AFAR2G
Manufacturer:
ON/安森美
Quantity:
20 000
Company:
Part Number:
nbc12430AFN
Manufacturer:
ON Semiconductor
Quantity:
10 000
Company:
Part Number:
nbc12430AFNG
Manufacturer:
ON Semiconductor
Quantity:
29
Part Number:
nbc12430AFNG
Manufacturer:
ON/安森美
Quantity:
20 000
Company:
Part Number:
nbc12430FAG
Manufacturer:
ON
Quantity:
58
Company:
Part Number:
nbc12430FAG
Manufacturer:
ON Semiconductor
Quantity:
1
Company:
Part Number:
nbc12430FAR2G
Manufacturer:
ON Semiconductor
Quantity:
2 750
Part Number:
nbc12430FAR2G
Manufacturer:
ON/安森美
Quantity:
20 000
accomplished by properly configuring the internal dividers
to produce the desired frequency at the outputs. The output
frequency can by represented by this formula:
where F
modulus, and N is the output divider modulus. Note that it
is possible to select values of M such that the PLL is unable
to achieve loop lock. To avoid this, always make sure that M
is selected to be 200 ≤ M ≤ 400 for a 16 MHz input reference.
above equation reduces to:
Substituting the four values for N (1, 2, 4, 8) yields:
*For crystal frequency of 16 MHz.
desired frequency from the above equations. The four output
frequency ranges established by N are 400- 800 MHz,
200- 400 MHz, 100- 200 MHz and 50- 100 MHz, respectively.
From these ranges, the user will establish the value of N
required. The value of M can then be calculated based on
equation 1. For example, if an output frequency of 131 MHz
was desired, the following steps would be taken to identify the
appropriate M and N values. 131 MHz falls within the
frequency range set by an N value of 4; thus, N [1:0] = 01.
For N = 4, F
M = 131 x 2 = 262, so M[8:0] = 100000110. Following this
same procedure, a user can generate any whole frequency
desired between 50 and 800 MHz. Note that for N > 2,
fractional values of F
programmable frequency steps (and thus, the indicator of the
fractional output frequencies achievable) will be equal to
F
Table 5, which shows the usable VCO frequency and M
divider range.
Table 4. Programmable Output Divider Function Table
N1
XTAL
1
0
0
1
Programming the NBC12430 and NBC12430A is
Assuming that a 16 MHz reference frequency is used the
The user can identify the proper M and N values for the
For input reference frequencies other than 16 MHz, see
F OUT + ((F XTAL or F REF_EXT ) B 16)
N0
÷ 16 ÷ N.
1
0
1
0
XTAL
Divider
OUT
B1
B2
B4
B8
is the crystal frequency, M is the loop divider
N
= M ÷ 2 and M = 2 x F
F OUT + 2M B N
M B 2
M B 4
OUT
M
F
OUT
M
can be realized. The size of the
2
Range (MHz)*
Frequency
400-800
200-400
100-200
50-100
Output
OUT
PROGRAMMING INTERFACE
NBC12430, NBC12430A
2M B N
. Therefore,
500 kHz
250 kHz
2 MHz
1 MHz
F
Step
http://onsemi.com
OUT
(eq. 1)
(eq. 2)
9
divider M is limited by the VCO frequency range and
F
range of 400 to 800 MHz in order to achieve stable PLL
operation.
stability. If the value for M fell outside of the valid range, a
different N value would be selected to move M in the
appropriate direction.
parallel or serial interface. The parallel interface is
controlled via the P_LOAD signal such that a LOW to HIGH
transition will latch the information present on the M[8:0]
and N[1:0] inputs into the M and N counters. When the
P_LOAD signal is LOW, the input latches will be
transparent and any changes on the M[8:0] and N[1:0] inputs
will affect the F
S_CLOCK signal samples the information on the S_DATA
line and loads it into a 14 bit shift register. Note that the
P_LOAD signal must be HIGH for the serial load operation
to function. The Test register is loaded with the first three
bits, the N register with the next two, and the M register with
the final nine bits of the data stream on the S_DATA input.
For each register, the most significant bit is loaded first (T2,
N1, and M8). A pulse on the S_LOAD pin after the shift
register is fully loaded will transfer the divide values into the
counters. The HIGH to LOW transition on the S_LOAD
input will latch the new divide values into the counters.
Figures 5 and 6 illustrate the timing diagram for both a
parallel and a serial load of the device synthesizer.
power-up through the parallel interface, and then possibly
again through the serial interface. This approach allows the
application to come up at one frequency and then change or
fine-tune the clock as the ability to control the serial
interface becomes available.
internal nodes as determined by the T[2:0] bits in the serial
configuration stream. It is not configurable through the
parallel interface. The T2, T1, and T0 control bits are preset
to `000' when P_LOAD is LOW so that the PECL F
outputs are as jitter-free as possible. Any active signal on the
TEST output pin will have detrimental affects on the jitter
of the PECL output pair. In normal operations, jitter
specifications are only guaranteed if the TEST output is
static. The serial configuration port can be used to select one
of the alternate functions for this pin.
XTAL
The input frequency and the selection of the feedback
The value for M falls within the constraints set for PLL
The M and N counters can be loaded either through a
M[8:0] and N[1:0] are normally specified once at
The TEST output provides visibility for one of the several
. M must be configured to match the VCO frequency
M min + f VCOmin B 2(f XTAL B 16) and
M max + f VCOmax B 2(f XTAL B 16)
OUT
output pair. To use the serial port, the
(eq. 3)
(eq. 4)
OUT