adns-2001 Avago Technologies, adns-2001 Datasheet
adns-2001
Related parts for adns-2001
adns-2001 Summary of contents
Page 1
... Description The ADNS-2001 is a low-cost reflective optical sensor that provides a non-mechanical tracking engine for implementing a computer mouse based on optical navigation technology which measures changes in position by optically acquiring sequential surface images (frames) and mathematic- ally determining the direction and magnitude of movement. The ...
Page 2
... LEAD OFFSET (0.050) 2.54 LEAD PITCH (0.100) (0.527) Figure 2. ADNS-2001 sensor package outline drawing. 2 system provided by the HDNS- 2100, HDNS-2200, and the HLMP-ED80. These images are further processed by the DSP to determine direction and distance of motion. The DSP generates a stream of delta x and delta y rela- ...
Page 3
... VDD5 5 VDC Input 15 NRESET NRESET 16 PS2_D PS/2 Interface Data 2D Assembly Drawing of ADNS-2001 Shown with HDNS-2100, HDNS- 2200, and HLMP-ED80. Agilent provides an IGES file drawing describing the base plate molding features for lens and PCB alignment. Please contact sales representative or visit our web site. Also, see HDNS-2100 Technical Data Sheet for more information ...
Page 4
... GND ( BUTTONS Note: 0.1 F between pins 7 and 8 must be ceraminc, and must be trace lengths less than 5 mm. 4 HDNS-2200 (CLIP) HLMP-ED80 (LED) ADNS-2001 (SENSOR) CUSTOMER SUPPLIED PCB HDNS-2100 (LENS) CUSTOMER SUPPLIED BASE PLATE WITH RECOMMENDED ALIGNMENT FEATURES PER IGES DRAWING 3.3 V REGULATOR LP2950ACZ-3 ...
Page 5
... Notes: 1. Due to the Cypress implementation of USB suspend mode support, the NRESET pin of the ADNS-2001 must be reset using a line from the Cypress chip. The reason for this is that the Cypress chip does not configure the port input pins until after it has received a bus reset from the USB port. ...
Page 6
Recommended LED Bin Table LED Bin Category R1 Value K 69.8 L 69.8 M 69.8 N 69.8 P 69.8 – 78.7 Q 69.8 – 93.1 R 69.8 – 113 S 69.8 – 137 T 69.8 – 169 Absolute Maximum Ratings ...
Page 7
Recommended Operating Conditions Parameter Operating Temperature Supply Voltage Supply Voltage Clock Frequency Resonator Impedance Reset Capacitor Distance from Lens Reference Plane to Surface Speed Acceleration Light Level onto IC DC Electrical Specifications Electrical Characteristics over recommended operating conditions. Typical values ...
Page 8
... I/O Specifications PS/2 Command Set Implementation The following commands are implemented. All other commands will cause an FE (resend) response from the ADNS-2001. A second invalid command will cause an FC (error) response from the ADNS-2001. Hex Command Mnemonic for and Response Command Bytes RESET RESEND FE nn ...
Page 9
PS/2 Mode Output Waveforms @ 24 MHz Host Sending Data Timing Diagram I/O INHIBIT CLK T1 DATA START BIT (1) Notes: 1. The mouse checks the DATA line. If the line is low, the system has data to transmit. The ...
Page 10
Quadrature Output Mode Waveform @ 24 MHz The 2 channel quadrature outputs are 5 V CMOS outputs. The Delta X count is used to generate the XA and XB quadrature signals. The Delta Y count is used to gen- erate ...
Page 11
... Typical Performance Characteristics Typical Performance of ADNS-2001 assembled as shown in Figure 3 with HDNS-2100 Lens, HDNS-2200 LED Assembly Clip and HLMP-ED80. 450 400 350 300 250 RECOMMENDED DISTANCE FROM 200 LENS FOOT 150 REFERENCE PLANE 100 TO SURFACE 50 0 2.0 2.2 2.4 2.6 2.8 3.0 3.2 DISTANCE FROM HDNS-2100 LENS FOOT REFERENCE PLANE TO SURFACE (mm) Figure 5 ...
Page 12
... Ordering Information Specify Part Number as follows: ADNS-2001 = Sensor 16-pin optical plastic package, 20 per tube, 1000 pieces in a box. ADNB-2012 = ADNS-2001 Sensor and HDNS-2100 Round Lens Bundle Kit, 1000 pieces incremental (e.g., ADNB-2012: 1000 pieces = 1000 pieces of ADNS-2001 and 1000 pieces of HDNS-2100 in a box). ...