cy28445-5 SpectraLinear Inc, cy28445-5 Datasheet - Page 15
![no-image](/images/no-image-200.jpg)
cy28445-5
Manufacturer Part Number
cy28445-5
Description
Clock Generator For Intel Calistoga Chipset
Manufacturer
SpectraLinear Inc
Datasheet
1.CY28445-5.pdf
(26 pages)
Rev 1.1, June 30, 2007
CLKREQ# Assertion (CLKREQ# -> LOW)
All differential outputs that were stopped are to resume normal
operation in a glitch free manner. The maximum latency from
the assertion to active outputs is between 2–6 SRC clock
periods (2 clocks are shown) with all SRC outputs resuming
simultaneously. All stopped SRC outputs must be driven high
within 10 ns of CLKREQ# deassertion to a voltage greater than
200 mV.
CLKREQ# Deassertion (CLKREQ# -> HIGH)
The impact of deasserting the CLKREQ# pins is all SRC
outputs that are set in the control registers to stoppable via
deassertion of CLKREQ# are to be stopped after their next
transition. The final state of all stopped DIF signals is low, both
SRCT clock and SRCC clock outputs will not be driven.PD
(Power-down) Clarification
The VTT_PWRGD# /PD pin is a dual-function pin. During
initial power-up, the pin functions as VTT_PWRGD#. Once
VTT_PWRGD# has been sampled low by the clock chip, the
pin assumes PD functionality. The PD pin is an asynchronous
active high input used to shut off all clocks cleanly prior to
shutting off power to the device. This signal is synchronized
internal to the device prior to powering down the clock synthe-
sizer. PD is also an asynchronous input for powering up the
system. When PD is asserted high, all clocks need to be driven
to a low value and held prior to turning off the VCOs and the
crystal oscillator.
PD Deassertion
The power-up latency is less than 1.8 ms. This is the time from
the deassertion of the PD pin or the ramping of the power
supply until the time that stable clocks are output from the
clock chip. All differential outputs stopped in a three-state
condition resulting from power down will be driven high in less
than 300 μs of PD deassertion to a voltage greater than
C PU C , 133M H z
C PU T , 133M H z
SR C C 100M H z
SR C T 100M H z
PC I, 33 M H z
U SB, 48M H z
D O T 96C
D O T 96T
R EF
PD
Figure 4. PD Assertion Timing Waveform
PD Assertion
When PD is sampled high by two consecutive rising edges of
CPUC, all single-ended outputs will be held low on their next
high to low transition and differential clocks must held high or
tri-stated (depending on the state of the control register drive
mode bit) on the next diff clock# high to low transition within 4
clock periods. When the SMBus PD drive mode bit corre-
sponding to the differential (CPU, SRC, and DOT) clock output
of interest is programmed to ‘0’, the clock output are held with
“Diff clock” pin driven high at 2 x Iref, and “Diff clock#” tristate.
If the control register PD drive mode bit corresponding to the
output of interest is programmed to “1”, then both the “Diff
clock” and the “Diff clock#” are tri-state. Note the example
below shows CPUT = 133 MHz and PD drive mode = ‘1’ for all
differential outputs. This diagram and description is applicable
to valid CPU frequencies 100, 133, 166, and 200 MHz. In the
event that PD mode is desired as the initial power-on state, PD
must be asserted high in less than 10 μs after asserting
Vtt_PwrGd#. It should be noted that 96_100_SSC will follow
the DOT waveform is selected for 96 MHz and the SRC
waveform when in 100-MHz mode.
200 mV. After the clock chip’s internal PLL is powered up and
locked, all outputs will be enabled within a few clock cycles of
each other. Below is an example showing the relationship of
clocks coming up. It should be noted that 96_100_SSC will
follow the DOT waveform is selected for 96 MHz and the SRC
waveform when in 100-MHz mode.
CY28445-5
Page 15 of 26