LM3S1637 Luminary Micro, Inc, LM3S1637 Datasheet - Page 65
![no-image](/images/no-image-200.jpg)
LM3S1637
Manufacturer Part Number
LM3S1637
Description
Lm3s1637 Arm Microcontroller
Manufacturer
Luminary Micro, Inc
Datasheet
1.LM3S1637.pdf
(547 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM3S1637-EQC50-A2
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
LM3S1637-EQC50-A2T
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
LM3S1637-IBZ50-A2
Manufacturer:
TI
Quantity:
264
Company:
Part Number:
LM3S1637-IBZ50-A2
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
LM3S1637-IBZ50-A2T
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
LM3S1637-IQC50-A2
Manufacturer:
Texas Instruments
Quantity:
10 000
- Current page: 65 of 547
- Download datasheet (6Mb)
6.1.4.1
July 25, 2008
Fundamental Clock Sources
There are four clock sources for use in the device:
■
■
■
■
The internal system clock (SysClk), is derived from any of the four sources plus two others: the
output of the main internal PLL, and the internal oscillator divided by four (3 MHz ± 30%). The
frequency of the PLL clock reference must be in the range of 3.579545 MHz to 8.192 MHz (inclusive).
The Run-Mode Clock Configuration (RCC) and Run-Mode Clock Configuration 2 (RCC2)
registers provide control for the system clock. The RCC2 register is provided to extend fields that
offer additional encodings over the RCC register. When used, the RCC2 register field values are
used by the logic over the corresponding field in the RCC register. In particular, RCC2 provides for
a larger assortment of clock configuration options.
Figure 6-3 on page 66 shows the logic for the main clock tree. The peripheral blocks are driven by
the system clock signal and can be programmatically enabled/disabled. The ADC clock signal is
automatically divided down to 16 MHz for proper ADC operation. The PWM clock signal is a
synchronous divide by of the system clock to provide the PWM circuit with more range.
Internal Oscillator (IOSC): The internal oscillator is an on-chip clock source. It does not require
the use of any external components. The frequency of the internal oscillator is 12 MHz ± 30%.
Applications that do not depend on accurate clock sources may use this clock source to reduce
system cost. The internal oscillator is the clock source the device uses during and following POR.
If the main oscillator is required, software must enable the main oscillator following reset and
allow the main oscillator to stabilize before changing the clock reference.
Main Oscillator (MOSC): The main oscillator provides a frequency-accurate clock source by
one of two means: an external single-ended clock source is connected to the OSC0 input pin, or
an external crystal is connected across the OSC0 input and OSC1 output pins. If the PLL is being
used, the crystal value must be one of the supported frequencies between 3.579545 MHz through
8.192 MHz (inclusive). If the PLL is not being used, the crystal may be any one of the supported
frequencies between 1 MHz and 8.192 MHz. The single-ended clock source range is from DC
through the specified speed of the device. The supported crystals are listed in the XTAL bit field
in the RCC register (see page 79).
Internal 30-kHz Oscillator: The internal 30-kHz oscillator is similar to the internal oscillator,
except that it provides an operational frequency of 30 kHz ± 50%. It is intended for use during
Deep-Sleep power-saving modes. This power-savings mode benefits from reduced internal
switching and also allows the main oscillator to be powered down.
External Real-Time Oscillator: The external real-time oscillator provides a low-frequency,
accurate clock reference. It is intended to provide the system with a real-time clock source. The
real-time oscillator is part of the Hibernation Module (“Hibernation Module” on page 122) and may
also provide an accurate source of Deep-Sleep or Hibernate mode power savings.
Preliminary
LM3S1637 Microcontroller
65
Related parts for LM3S1637
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![LM3-100K-TR](/images/no-image3.png)
Part Number:
Description:
Inductor: Molded: 10u: 10%: 30M: 7.9: 440m: Axial: T/R
Manufacturer:
Inductor Supply, Inc.
![LM3-R15](/images/no-image3.png)
Part Number:
Description:
Molded Inductor
Manufacturer:
Inductor Supply, Inc.
Datasheet:
![LM3-PWN1-01-N1](/images/no-image3.png)
Part Number:
Description:
Cree Smd Led
Manufacturer:
Cree, Inc.
Datasheet:
![LM3-PBL1-01-N1](/images/no-image3.png)
Part Number:
Description:
Cree Smd Led
Manufacturer:
Cree, Inc.
Datasheet:
![LM3-EWN1-01-N1-MT](/images/no-image3.png)
Part Number:
Description:
Specification For Cotco Led Lamp
Manufacturer:
Marktech Optoelectronics
Datasheet:
![LM3S1110](/images/no-image3.png)
Part Number:
Description:
Lm3s1110 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
![LM3S1133](/images/no-image3.png)
Part Number:
Description:
Lm3s1133 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
![LM3S1138](/images/no-image3.png)
Part Number:
Description:
Lm3s1138 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
![LM3S1150](/images/no-image3.png)
Part Number:
Description:
Lm3s1150 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
![LM3S1162](/images/no-image3.png)
Part Number:
Description:
Lm3s1162 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
![LM3S1165](/images/no-image3.png)
Part Number:
Description:
Lm3s1165 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
![LM3S1332](/images/no-image3.png)
Part Number:
Description:
Lm3s1332 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
![LM3S1435](/images/no-image3.png)
Part Number:
Description:
Lm3s1435 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet: