HT46RB50 Holtek Semiconductor, HT46RB50 Datasheet - Page 4
![no-image](/images/no-image-200.jpg)
HT46RB50
Manufacturer Part Number
HT46RB50
Description
A/D Type USB 8-Bit MCU
Manufacturer
Holtek Semiconductor
Datasheet
1.HT46RB50.pdf
(53 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HT46RB50
Manufacturer:
TI
Quantity:
5 580
Company:
Part Number:
HT46RB50
Manufacturer:
HOLTEK
Quantity:
6
Absolute Maximum Ratings
Supply Voltage ...........................V
Input Voltage..............................V
I
Total Power Dissipation .....................................500mW
Note: These are stress ratings only. Stresses exceeding the range specified under Absolute Maximum Ratings may
D.C. Characteristics
Rev. 1.10
OL
V
I
I
I
I
PE2/SDI
PE3/SDO
PE4~PE5
RES
VSS
AVSS
VDD
AVDD
OSC1
OSC2
V33O
UDP
UDN
DD1
DD2
STB1
STB2
Symbol
DD
Pin Name
Total ..............................................................150mA
cause substantial damage to the device. Functional operation of this device at other conditions beyond those
listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliabil-
ity.
Operating Voltage
Operating Current (6MHz Crystal)
Operating Current (12MHz Crystal)
Standby Current (WDT Enabled)
Standby Current (WDT Disabled)
I/O
I/O
I/O
I/O
I/O
I/O
O
O
I
I
(nibble option)
(nibble option)
(nibble option)
Parameter
Pull-high
Pull-high
Pull-high
Options
SS
SS
0.3V to V
0.3V to V
Bidirectional I/O lines. Software instructions determine the CMOS output or
Schmitt trigger input with pull-high resistor (determined by pull-high options:
nibble option). The PE2 is pin-shared with SDI. SDI is Serial interface serial
input.
Bidirectional I/O lines. Software instructions determine the CMOS output or
Schmitt trigger input with pull-high resistor (determined by pull-high options:
nibble option). The PE3 is pin-shared with SDO. SDO is a Serial interface
serial output.
Bidirectional I/O lines. Software instructions determine the CMOS output or
Schmitt trigger input with pull-high resistor (determined by pull-high options:
nibble option).
Schmitt trigger reset input, active low
Negative power supply, ground
ADC negative power supply, ground
Positive power supply
ADC positive power supply, AVDD should be externally connected to VDD.
OSC1 and OSC2 are connected to a 6MHz or 12MHz Crystal/resonator (de-
termined by software instructions) for the internal system clock.
3.3V regulator output.
UDP is USBD+ line
USB function is controlled by software control register.
UDN is USBD- line
USB function is controlled by software control register.
DD
SS
+6.0V
+0.3V
V
5V No load, f
3V
5V
3V No load, system HALT,
5V
3V No load, system HALT,
5V
DD
Test Conditions
f
f
No load, f
USB suspended
USB suspended
SYS
SYS
4
=6MHz
=12MHz
Conditions
Storage Temperature ............................ 50 C to 125 C
Operating Temperature........................... 40 C to 85 C
I
OH
SYS
SYS
Total............................................................ 100mA
=6MHz
=12MHz
Description
Min.
2.2
2.7
Typ.
6.5
3.6
7.5
September 7, 2006
HT46RB50
Max.
5.5
5.5
12
10
16
10
5
1
2
Ta=25 C
Unit
mA
mA
mA
V
V
A
A
A
A