ACS8520T Semtech, ACS8520T Datasheet - Page 19
![no-image](/images/manufacturer_photos/0/5/595/semtech_sml.jpg)
ACS8520T
Manufacturer Part Number
ACS8520T
Description
Synchronous Equipment Timing Source (SETS) for Stratum 3/4E/4 and SMC Systems
Manufacturer
Semtech
Datasheet
1.ACS8520T.pdf
(150 pages)
- Current page: 19 of 150
- Download datasheet (2Mb)
It is also possible to combine the internal averaging filters
with some additional software filtering. For example the
internal fast filter could be used as an anti-aliasing filter
and the software could further filter this before
determining the actual Holdover frequency. To support
this feature, a facility to read out the internally averaged
frequency has been provided. By setting Reg. 40, Bit 5,
cnfg_holdover_modes, read_average, the value read
back from the cnfg_holdover_frequency register will be
the filtered value. The filtered value is available
regardless of what actual Holdover mode is selected.
Clearly this results in the register not reading back the
data that was written to it.
Example: Software averaging to eliminate temperature drift.
Select Manual Holdover mode by setting Reg. 34 Bit 4,
cnfg_input_mode, man_holdover High.
Select Fast Holdover Averaging mode by setting Reg. 40
Bit 6, cnfg_holdover_modes, auto_averaging High and
Reg. 40 Bit 7 High.
Select to be able to read back filtered output by setting
Reg. 40 Bit 5, cnfg_holdover_modes, read_average High.
Software periodically reads averaged value from the
cnfg_holdover_frequency register and the temperature
(not supplied from ACS8520). Software processes
frequency and temperature and places data in software
look-up table or other algorithm. Software writes back
appropriate averaged value into the
cnfg_holdover_frequency register.
Once Holdover mode is entered, software periodically
updates the cnfg_holdover_frequency register using the
temperature information (not supplied from ACS8520).
Mini-holdover Mode
Holdover mode so far described refers to a state to which
the internal state machine switches as a result of activity
or frequency alarms, and this state is reported in Reg. 09.
To avoid the DPLL’s frequency being pulled off as a result
of a failed input, then the DPLL has a fast mechanism to
freeze its current frequency within one or two cycles of the
input clock source stopping. Under these circumstances
the DPLL enters Mini-holdover mode; the Mini-holdover
frequency used being determined by Reg. 40, Bits [4:3],
cnfg_holdover_modes, mini_holdover_mode.
Revision 3.02/October 2005 © Semtech Corp.
ADVANCED COMMUNICATIONS
FINAL
Page 19
Mini-holdover mode only lasts until one of the following
happens:
External Factors Affecting Holdover Mode
If the external TCXO/OCXO frequency is varying due to
temperature fluctuations in the room, then the
instantaneous value can be different from the average
value, and then it may be possible to exceed the 0.05
ppm limit (depending on how extreme the temperature
fluctuations are). It is advantageous to shield the
TCXO/OCXO to slow down frequency changes due to drift
and external temperature fluctuations.
The frequency accuracy of Holdover mode has to meet the
ITU-T, ETSI and Telcordia performance requirements. The
performance of the external oscillator clock is critical in
this mode, although only the frequency stability is
important - the stability of the output clock in Holdover is
directly related to the stability of the external oscillator.
Pre-locked2 Mode
This state is very similar to the Pre-Locked state. It is
entered from the Holdover state when a reference source
has been selected and applied to the phase locked loop.
It is also entered if the device is operating in Revertive
mode and a higher-priority reference source is restored.
Upon applying a reference source to the phase locked
loop, the ACS8520 will enter the Locked state in a
maximum of 100 seconds, as defined by GR-1244-
CORE
of good quality.
If the device cannot achieve lock within 100 seconds, it
reverts to Holdover mode and another reference source is
selected.
DPLL Architecture and Configuration
A Digital PLL gives a stable and consistent level of
performance that can be easily programmed for different
dynamic behavior or operating range. It is not affected by
operating conditions or silicon process variations. Digital
synthesis is used to generate all required SONET/SDH
output frequencies. The digital logic operates at
204.8 MHz that is multiplied up from the external
12.800 MHz oscillator module. Hence the best resolution
A new source has been selected, or
The state machine enters Holdover mode, or
The original fault on the input recovers.
[19]
specification, if the selected reference source is
ACS8520 SETS
DATASHEET
www.semtech.com
Related parts for ACS8520T
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ACS-1024-LG](/images/no-image3.png)
Part Number:
Description:
Image Sensor, CMOS|CCD, 1026x1026 Pixels, 132pin LCC
Manufacturer:
Photon Vision Systems, Inc.
Datasheet:
![ACS-I1024-CPGA](/images/no-image3.png)
Part Number:
Description:
High Performance Area CMOS Image Sensor
Manufacturer:
Photon Vision Systems, Inc.
Datasheet:
![ACS-I2048-CPGA](/images/no-image3.png)
Part Number:
Description:
Image Sensor, CMOS, 2048x2048 Pixels, 144pin CPGA
Manufacturer:
Photon Vision Systems, Inc.
Datasheet:
![ACS-C018](/images/no-image3.png)
Part Number:
Description:
SMD Mini Spring Coils
Manufacturer:
ECM [ECM Electronics Limited.]
Datasheet:
![SC4501STDEVB](/images/manufacturer_photos/0/5/595/semtech_tmb.jpg)
Part Number:
Description:
EVALUATION BOARD
Manufacturer:
Semtech
Datasheet:
![SC4518HEVB-2](/images/manufacturer_photos/0/5/595/semtech_tmb.jpg)
Part Number:
Description:
EVALUATION BOARD
Manufacturer:
Semtech
Datasheet:
![60KS200C](/images/manufacturer_photos/0/5/595/semtech_tmb.jpg)
Part Number:
Description:
VOLTAGE SUPPRESSOR, TRANSIENT SEMTECH
Manufacturer:
Semtech
Datasheet:
![6666](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
HIGH VOLTAGE CAPACITORS MONOLITHIC CERAMIC TYPE
Manufacturer:
Semtech Corporation
Datasheet:
![EZ1084CM](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
EZ1084CM5.0 AMP POSITIVE VOLTAGE REGULATOR
Manufacturer:
Semtech Corporation
Datasheet:
![EZ1587CM](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
3.0 AMP LOW DROPOUT POSITIVE VOLTAGE REGULATORS
Manufacturer:
Semtech Corporation
Datasheet: