ACS8520T Semtech, ACS8520T Datasheet - Page 129
ACS8520T
Manufacturer Part Number
ACS8520T
Description
Synchronous Equipment Timing Source (SETS) for Stratum 3/4E/4 and SMC Systems
Manufacturer
Semtech
Datasheet
1.ACS8520T.pdf
(150 pages)
- Current page: 129 of 150
- Download datasheet (2Mb)
Address (hex):
Address (hex):
Revision 3.02/October 2005 © Semtech Corp.
ADVANCED COMMUNICATIONS
Register Name
Register Name
ph_offset_ramp
indep_FrSync/
MFrSync
Bit No.
Bit No.
Bit 7
[1:0]
Bit 7
[6:4]
7
7B (cont...)
7C
cnfg_sync_phase
Description
Sync_phase
Register to control the sampling of the external Sync
input. Nominally the falling edge of the input is
aligned with the falling edge of the reference clock.
The margin is ±0.5 U.I. (Unit Interval).
cnfg_sync_monitor
Description
ph_offset_ramp
Register bit to force an internal phase offset
calibration, see Reg. 71, Cnfg_Phase_Offset.
The calibration routine is transparent to the outside
and puts the device in holdover while it internally
ramps the phase offset to zero, resets all internal
output and feedback dividers and then ramps the
phase offset to the current programmed value from
Reg. 70 or 71., holdover is then turned off. All this is
transparent to the outside with no change in output
phase offset visible.
Sync_monitor_limit
An alternative to allowing the external Sync input to
synchronize the outputs, is to use the Sync monitor
block to alarm when the external Sync input does
not align with the output within a certain number of
input clock cycles. This register defines the limit in
UI of the selected reference source. If the alignment
does not occur within this limit, then Sync alarm will
be raised, see Reg. 09 Bit 7.
Sync_OC-N_
rates
Bit 6
Bit 6
Sync_monitor_limit
Bit 5
Bit 5
Description
Description
Bit 4
Bit 4
FINAL
Page 129
(R/W) Register to configure the
behavior of the synchronization
for the external frame reference.
(R/W) Register to configure the
external Sync input monitor. It
also has a bit to control the phase
offset automatic ramping feature.
Bit Value
Bit Value
Bit 3
Bit 3
000
001
010
011
100
101
110
111
00
01
10
11
0
1
Value Description
On target.
0.5 U.I. early
1 U.I. late
0.5 U.I. late.
Value Description
Phase offset automatically ramped from the old
value to the new value when there is a change in
Reg. 70 or 71.
Start phase offset internal calibration routine. This
bit is reset to 0 when this is complete.
Sync alarm raised beyond ±1 UI.
Sync alarm raised beyond ±2 UI.
Sync alarm raised beyond ±3 UI.
Sync alarm raised beyond ±4 UI.
Sync alarm raised beyond ±5 UI.
Sync alarm raised beyond ±6 UI.
Sync alarm raised beyond ±7 UI.
Sync alarm raised beyond ±8 UI.
Sync_reference_source
Bit 2
Bit 2
Default Value
Sync_phase
Default Value
ACS8520 SETS
Bit 1
Bit 1
DATASHEET
www.semtech.com
0000 0000
0010 1011
Bit 0
Bit 0
Related parts for ACS8520T
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Image Sensor, CMOS|CCD, 1026x1026 Pixels, 132pin LCC
Manufacturer:
Photon Vision Systems, Inc.
Datasheet:
Part Number:
Description:
High Performance Area CMOS Image Sensor
Manufacturer:
Photon Vision Systems, Inc.
Datasheet:
Part Number:
Description:
Image Sensor, CMOS, 2048x2048 Pixels, 144pin CPGA
Manufacturer:
Photon Vision Systems, Inc.
Datasheet:
Part Number:
Description:
SMD Mini Spring Coils
Manufacturer:
ECM [ECM Electronics Limited.]
Datasheet:
Part Number:
Description:
EVALUATION BOARD
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
EVALUATION BOARD
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
VOLTAGE SUPPRESSOR, TRANSIENT SEMTECH
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
HIGH VOLTAGE CAPACITORS MONOLITHIC CERAMIC TYPE
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
EZ1084CM5.0 AMP POSITIVE VOLTAGE REGULATOR
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
3.0 AMP LOW DROPOUT POSITIVE VOLTAGE REGULATORS
Manufacturer:
Semtech Corporation
Datasheet: