AD6426 Analog Devices, AD6426 Datasheet - Page 22
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
AD6426
Manufacturer Part Number
AD6426
Description
Enhanced GSM Processor
Manufacturer
Analog Devices
Datasheet
1.AD6426.pdf
(50 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD6426AB
Manufacturer:
AD
Quantity:
8 831
Company:
Part Number:
AD6426AST
Manufacturer:
ADI
Quantity:
455
Radio Interface
The AD6426 Radio Interface has been designed to support
direct connection to the ADI IF-Chips AD6432, while
providing full backwards compatibility to existing radio
designs interfacing to the AD20msp410 and AD20msp415.
Additionally the AD6426 Radio Interface supports radio
architectures based on Siemens, TTP/Hitachi or Philips RF
chipsets.
The Radio Interface of the AD6426 consists of 16 dedicated
output pins listed in Table 13. Together with two optional
general purpose I/O-pins they provide a flexible interface to a
variety of radio architectures for both 900 MHz and 1800/1900
MHz operation.
Dual Band Control
To support dual band handsets BANDSELECT[1:0] signals
are provided. BANDSELECT0 is multiplexed with GPIO[2],
with the default function of this being GPIO[2].
BANDSELECT1 is multiplexed with GPIO[1], the default
function being GPIO[1].
For Dual Band solutions requiring a single band select bit, the
BANDSELECT0 function is enabled by asserting the BAND
EN bit. In order to set BANDSELECT0 high/low and cause
the radio module to operate in the appropriate band, the least
significant bit (bit 0) of the relevant 32 bit register for
Dynamic Synthesizer 1 must be written, i.e. different values
may be set for Rx, Tx and Monitor but only for Dynamic
Synthesizer 1.
BANDSELECT0 is sampled internally and is valid from the
beginning of data serialization, both for on demand
(immediate) loading and ordinary interrupt driven loading.
The BANDSELECT0 signal will remain in this known state
until the next time there is any serialization of data for
Dynamic Synthesizer 1, when a new sample will be taken of
the least significant bit of the 32 bit synthesizer register
currently being serialized.
Full control is provided over the number of bits to be shifted
out to the synthesizer and so it is intended that this bit count
will always be less than 32 when using the BANDSELECT0
feature in order to prevent shifting the control bit out.
BANDSELECT0 is gated with RADIO POWER CONTROL to
ensure that whenever the RADIO is off, BANDSELECT0 is
forced to a low state.
For Dual Band Solution requiring two band select bits, one for
GSM900, and one for DCS1800, then both BANDSELECT0
and BANDSELECT1 are enabled by asserting both the BAND
EN and DCSSEL EN bits. The BANDSELECT0 output is
driven as in the single enable mode (described above), and the
BANDSELECT1 output is the inverted output of the raw
BANDSELECT0 output (prior to gating with RADIO POWER
This Information applies to a product under development. Its characteristics and specifications are subject to change without notice. Analog Devices assumes no
obligation regarding future manufacture unless otherwise agreed to in writing. No responsibility is assumed by Analog Devices for its use; nor for any
infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent
rights of Analog Devices.
Revision Preliminary 2.3 (June 9, ´98)
Preliminary Technical Information
- 22 -
CONTROL), gated with RADIO POWER CONTROL to force
a low output when the Radio is off.
In order to increase the flexibility of the AD6426, three pins in
the Radio Interface are multiplexed with GPO functions. The
pins multiplexed are: SYTHEN1, AGCA and AGCB, with the
default function being the Radio Interface.
The mode of these pins is controlled by the new ccGPO
Channel Codec Register:
The GPO[n]Sel bit selects the function of the pin. Setting
GPO[n]Sel to one will enable the pin to be controlled by the
GPO[n] bit. The GPO[n]Sel bit will override any other pin
function selection.
Generic Pins
The following three pins have the same functionality in all
types of radio architectures:
RADIOPWRCTL
This output signal is typically used to power down the
oscillators and prescalers during Idle mode and is directly
controlled by the Radio Power Control flag in the POWER
CONTROL EXTERNAL CC Control Register 45.
Name
GPIO1
GPIO2
RADIOPWRCTL
GPIO6
GPIO7
TXPHASE
TXENABLE
TXPA
RXON
CALIBRATERADIO
SYNTHEN0
SYNTHEN1
SYNTHDATA
SYNTHCLK
AGCA
AGCB
Bit
1
POWER CONTROL EXTERNAL CC Control
Register 45
Radio Power Control
Table 13. Radio Interface
I/O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Confidential Information
Function
BANDSELECT1
BANDSELECT0
Radio Powerdown Control
VBIAS
ANTENNASELECT
Switches PLLs (Rx / Tx)
Transmit Enable
Power Amplifier Enable
Receiver on
Radio Calibration
Synthesizer 0 Enable
Synthesizer 1 Enable
Synthesizer Port Serial Data
Synthesizer Port Clock
AGC Control A
AGC Control B
AD6426