MT9074 Mitel Networks Corporation, MT9074 Datasheet - Page 4
![no-image](/images/no-image-200.jpg)
MT9074
Manufacturer Part Number
MT9074
Description
T1/E1/J1 Single Chip Transceiver
Manufacturer
Mitel Networks Corporation
Datasheet
1.MT9074.pdf
(122 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MT9074AL
Manufacturer:
ZARLINK
Quantity:
1 238
Company:
Part Number:
MT9074AL1
Manufacturer:
ZARLINK
Quantity:
22
Company:
Part Number:
MT9074AP
Manufacturer:
MITEL
Quantity:
14
Part Number:
MT9074AP
Manufacturer:
ZARLINK
Quantity:
20 000
Company:
Part Number:
MT9074AP1
Manufacturer:
ZARLINK
Quantity:
227
Company:
Part Number:
MT9074APR1
Manufacturer:
ZARLINK
Quantity:
227
MT9074
Pin Description
4
68 Pin
PLCC
21 -
26 -
17
18
19
20
24
25
30
31
32
33
34
35
36
37
38
39
40
41
Pin #
99, 8-11 AC0 - AC4 Address/Control 0 to 4 (Inputs). Address and control inputs for the non-
100 Pin
MQFP
94-97
90
91
92
93
98
12
13
14
15
16
17
18
19
20
21
22
RxDLCLK Data Link Clock (Output). A gapped clock signal derived from the extracted clock
INT/MOT
R/W/WR
GND
VDD
D4 - D7
RRING
Name
RxDL
TxMF
RTIP
VDD
VDD
VSS
TxA
TxB
Vss
IC
ARx
ARx
Negative Power Supply (Input). Digital ground.
Internal Connection. Tie to Vss (ground) for normal operation.
Intel/Motorola Mode Selection (Input).A high on this pin configures the
processor interface for the Intel parallel non-multiplexed bus type. A low configures
the processor interface for the Motorola parallel non-multiplexed type.
Positive Power Supply (Input). Digital supply (+5V 5%).
Data 4 to Data 7 (Three-state I/O). These signals combined with D0-D3 form the
bidirectional data bus of the parallel processor interface (D7 is the most significant
bit).
Read/Write/Write Strobe (Input). In Motorola mode (R/W), this input controls the
direction of the data bus D[0:7] during a microprocessor access. When R/W is
high, the parallel processor is reading data from the MT9074. When low, the
parallel processor is writing data to the MT9074. For Intel mode (WR), this active
low write strobe configures the data bus lines as output.
multiplexed parallel processor interface. AC0 is the least significant input.
Receive Analog Ground (Input). Analog ground for the LIU receiver.
Receive TIP and RING (Input). Differential inputs for the receive line signal - must
be transformer coupled (See Figure 5). In digital framer mode these are TTL level
inputs that connect to the digital outputs of a receiver. If the receiver serial data
output is NRZ connect that output to RTIP. If the receiver data output is split phase
unipolar signal connect one signal to RTIP and the complementary signal to
RRING.
Receive Analog Power Supply (Input). Analog supply for the LIU receiver (+5V
5%).
Positive Power Supply (Input). Digital supply (+5V
Negative Power Supply (Input). Digital ground.
Transmit A (Output). When the internal LIU is disabled (digital framer only
mode), if control bit NRZ=1, and NRZ output data is clocked out on pin TxA with
the rising edge of C1.50 (TxB has no function when NRZ format is selected). If
NRZ=0, pins TxA and TxB are a complementary pair of signals that output digital
dual-rail clocked out with the rising edge of C1.50.
Transmit B (Output). When the internal LIU is disabled and control bit NRZ=0,
pins TxA and TxB are a complementary pair of signals that output digital dual-rail
data clocked out with the rising edge of C1.50.
from the line clock, available for an external device to clock in RxDL data (at 4, 8,
12, 16 or 20 kHz) on the rising edge.
Receive Data Link (Output). A serial bit stream containing received line data after
zero code suppression. This data is clocked out with the rising edge of E1.5o.
Transmit Multiframe Boundary (Input). An active low input used to set the
transmit multiframe boundary (CAS or CRC multiframe). The MT9074 will generate
its own multiframe if this pin is held high. This input is usually pulled high for most
applications.
Description
Advance Information
5%).