MD3331-D64-V3 M-Systems Inc., MD3331-D64-V3 Datasheet - Page 11

no-image

MD3331-D64-V3

Manufacturer Part Number
MD3331-D64-V3
Description
Diskonchip Millennium Plus
Manufacturer
M-Systems Inc.
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MD3331-D64-V3
Manufacturer:
M-SYSTEMS
Quantity:
334
Part Number:
MD3331-D64-V3-X
Manufacturer:
SANDISK
Quantity:
18 135
Part Number:
MD3331-D64-V3-X
Manufacturer:
TI
Quantity:
699
Part Number:
MD3331-D64-V3-X
Quantity:
1 000
Part Number:
MD3331-D64-V3-X
Manufacturer:
M-SYSTEMS
Quantity:
20 000
Company:
Part Number:
MD3331-D64-V3-X
Quantity:
24
Company:
Part Number:
MD3331-D64-V3-X
Quantity:
1 545
2.2.3 Signal Descriptions
DiskOnChip Millennium Plus TSOP-I and BGA packages support identical signals. The related pin and ball
designations are listed in the signal descriptions, presented in logic groups, in Table 1 and Table 2.
TSOP-I Package
11
A[12:6]
A[5:0]
BHE#
CE#
D[7:0]
D[15:8]
OE#
WE#
ID[1:0]
IF_CFG
LOCK#
BUSY#
IRQ#
RSTIN#
Signal
Pin No.
26, 24
14-19
35-28
46-39
5-11
20
22
23
27
47
2
4
3
1
Table 1: Standard Interface Signal Descriptions, TSOP-I Package
ST, R8 Byte High Enable, active low. When low, data transaction on
IN, R8 Data bus, high byte. Not used and may be left floating when
ST, R Chip Enable, active low.
Input
Type
OD
ST
ST
ST
ST
ST
ST
ST
IN
-
Address bus.
D[15:8] is enabled. Not used and may be left floating when IF_CFG
is set to 0 (8-bit mode).
Data bus, low byte.
IF_CFG is set to 0 (8-bit mode).
Output Enable, active low.
Write Enable, active low.
Identification. For DiskOnChip 16MB/32MB, up to four chips can be
cascaded in the same memory window, according to the following
assignment:
Chip 1 = ID1, ID0 = VSS, VSS (0,0); required for single chip
Chip 2 = ID1, ID0 = VSS, VCC (0,1)
Chip 3 = ID1, ID0 = VCC, VSS (1,0)
Chip 4 = ID1, ID0 = VCC, VCC (1,1)
For DiskOnChip 64MB, up to two chips can be cascaded in the
same memory window, according to the following assignment:
Chip 1 = ID1=VSS, ID0 = VSS; required for single chip
Chip 2 = ID1=VSS, ID0 = VCC
Interface Configuration, 1 for 16-bit interface mode, 0 for 8-bit
interface mode.
Lock, active low. When active, provides full hardware data
protection of selected partitions.
Busy, active low, open drain. Indicates that DiskOnChip is
initializing and should not be accessed. A 10 K
required even if the pin is not used.
Interrupt Request. Requires a 10 K
Reset, active low.
Data Sheet, Rev. 1.7
System Interface
Configuration
Control
Description
 pull-up resistor.
DiskOnChip Millennium Plus 16/32/64MByte
pull-up resistor is
93-SR-002-03-8L
Signal
Output
Output
Output
Input/
Type
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input

Related parts for MD3331-D64-V3