MT8930C Zarlink Semiconductor, MT8930C Datasheet - Page 4
![no-image](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_sml.jpg)
MT8930C
Manufacturer Part Number
MT8930C
Description
4 Wire Full-duplex 2B+D (192 Kbps) Data Format Isdn S And T Subscriber Network Interface Circuit With Controllerless Mode
Manufacturer
Zarlink Semiconductor
Datasheet
1.MT8930C.pdf
(41 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MT8930CE
Manufacturer:
MITSUBISHI
Quantity:
20 000
Part Number:
MT8930CP
Manufacturer:
N/A
Quantity:
20 000
Company:
Part Number:
MT8930CP1
Manufacturer:
ZARLINK
Quantity:
12 388
Part Number:
MT8930CP1
Manufacturer:
ZARLINK
Quantity:
20 000
MT8930C
Pin Description (continued)
4
DIP
17
18
19
20
21
22
23
24
25
26
27
28
Pin #
12,15,18,
23,27-29,
1,5-6,10-
PLCC
33, 36,
39, 41
26
30
31
32
34
35
37
38
40
42
43
44
STAR/Rsto Star/Reset (Open Drain Output): 192kbit/s Rx data output fixed relative to the ST-BUS
SYNC/BA Synchronization/Bus Activity Output (Cmode = 0): output indicating synchronization
Name
MCH
MFR
V
LRx
M/S
Rsti
V
LTx
DR
NC
AR
Bias
DD
to incoming RX frames when activation request is asserted and the deactivation request
is ’0’ (AR = 1 and DR = 0). Synchronization is declared once three successive frames
conforming to the 14-bit bipolar violation criteria have been detected. If part is
deactivated or activation request is ’0’ (AR = 0 or DR = 1), this pin indicates the
presence of bus activity.
Multiframe Input/Output (Cmode=0): multiframe input in NT mode or output in TE
mode. Setting this pin to one in NT mode when HALF = 1, forces the F
respectively. This pin going high in TE mode indicates that F
received. This signal is updated on the rising edge of the HALF signal.
Maintenance Channel (Q-channel) Input/Output (Cmode=0): an output in NT mode
which is valid only in the frame following the transmission of MFR. In TE mode, this is
the maintenance channel (Q-channel) input which is transmitted in the F
following the reception of the multiframe signal. This input is sampled on the falling
edge of the HALF signal.
M/S Input/Output (Cmode=0): M/S bit input in NT mode or M/S bit output in TE mode.
M is read or written when HALF=1 while S is read or written when HALF=0.
Activate Request Input (Cmode = 0): asserting AR with DR = 0 will initiate the
appropriate S-interface activation sequence coded in the NT or TE activation/
deactivation controller.
Deactivate Request Input (Cmode = 0): asserting DR high will initiate the appropriate
S-interface deactivation sequence coded in the NT or TE activation/ deactivation
controller.
Reset Input: Schmitt trigger reset input. If ’0’, sets all control registers to the default
conditions, resets activation state machines to the deactivated state, resets HDLC,
clears the HDLC FIFO‘s. Sets the microport to Motorola bus mode.
timebase. A group of NTs, in fixed timing mode, can be wire or’ed together to create a
Star configuration. Active low reset output in TE mode indicating 128 consecutive
marks have been received. Can be connected directly to Rsti to allow NT to reset all
TEs on the bus. This pin must be tied to V
Receive Line Signal Input: this is a high impedance input for the pseudoternary line
signal to be connected to the line through a 2:1 ratio transformer. See Figures 20 and
21. A DC bias level on this input equal to V
Transmit Line Signal Output: this is a current source output designed to drive a
nominal 50 ohm line through a 2:1 ratio transformer. See Figures 20 and 21.
Bias Voltage: analog ground for Tx and Rx transformers. This pin must be decoupled
to V
tantalum).
Power Supply Input.
No Connection.
DD
through a 10µF capacitor with good high frequency characteristics (i.e.,
Description
DD
Bias
with a 10 kΩ resistor.
must be maintained.
A
= 1 & N= 0 has been
A
A
Data Sheet
, N pair to 1, 0
and L bits