STM8S105XX STMicroelectronics, STM8S105XX Datasheet - Page 37
STM8S105XX
Manufacturer Part Number
STM8S105XX
Description
(STM8S103XX / STM8S105XX) STM8S 8-bit MCU
Manufacturer
STMicroelectronics
Datasheet
1.STM8S105XX.pdf
(56 pages)
- Current page: 37 of 56
- Download datasheet (917Kb)
STM8S103xx, STM8S105xx
Table 11.
1. All power (V
2. I
3. Negative injection disturbs the analog performance of the device.
4. When several inputs are submitted to a current injection, the maximum
Table 12.
I
ΣI
INJ(PIN)
external supply.
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
there is no positive injection current, and the corresponding V
positive and negative injected currents (instantaneous values). These results are based on
characterization with
INJ(PIN)
Symbol
INJ(PIN)
Symbol
I
I
VDD
VSS
I
T
IO
STG
T
(2)(3)
J
must never be exceeded. This is implicitly insured if V
(2)
Current characteristics
Thermal characteristics
DD
, V
Total current into V
Total current out of V
Output current sunk by any I/O and control pin
Output current source by any I/Os and control pin
Injected current on NRST pin
Injected current on OSCIN pin
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
DDIO
Σ
, V
I
INJ(PIN)
IN
DDA
>V
) and ground (V
DD
Maximum junction temperature
maximum current injection on four I/O port pins of the device.
while a negative injection is induced by V
Storage temperature range
DD
SS
power lines (source)
Ratings
ground lines (sink)
SS
Ratings
, V
SSIO
(4)
, V
SSA
) pins must always be connected to the
IN
IN
maximum must always be respected
(1)
maximum is respected. If V
(1)
Σ
I
IN
INJ(PIN)
<V
INJ(PIN)
(4)
Electrical characteristics
SS
. For true open-drain pads,
-65 to +150
is the absolute sum of the
value. A positive
Value
150
www.DataSheet4U.com
± 20
Max.
- 20
± 4
± 4
± 4
60
60
20
IN
maximum
Unit
Unit
°C
mA
37/56
Related parts for STM8S105XX
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
STM8 touch sensing library
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
KIT STARTER FOR STM8S207/8 SER
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
EVAL KIT TOUCH SENSING STM8S
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR STM8S
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD DAUGHTER FOR STM8S207/8
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
EVAL KIT MOTOR CONTROL STM8S
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Raisonance’s complete, low-cost starter kits for STM8 and ST7
Manufacturer:
STMICROELECTRONICS [STMicroelectronics]
Datasheet:
Part Number:
Description:
EMULATOR FOR STM8
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
MCU, MPU & DSP Development Tools EvoPrimer Base MCU Target BRD w/Ext BRD
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
MCU, MPU & DSP Development Tools EvoPrimer Base Proto 5 Extention Boards
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet: