TEA1202 Philips Semiconductors, TEA1202 Datasheet
TEA1202
Available stocks
Related parts for TEA1202
TEA1202 Summary of contents
Page 1
... DATA SHEET TEA1202TS Battery power unit Objective specification File under Integrated Circuits, IC03 INTEGRATED CIRCUITS 2000 Jun 08 ...
Page 2
... TEA1202TS SSOP20 2000 Jun 08 GENERAL DESCRIPTION The TEA1202TS is a fully integrated battery power unit including a high-efficiency DC/DC converter which runs from a 1-cell NiCd or NiMH battery, two low dropout voltage regulators and a low battery detector. The circuit can be arranged in many ways to optimize the application circuit of a power supply system ...
Page 3
... 100 mA L PWM mode 480 6 V < 0.4 V 1.30 LDO LDO in regulation V > FB1,2 j 1.165 3 Objective specification TEA1202TS MIN. TYP. MAX. UNIT 5.50 V I(start) 5.50 V O(uvlo) 0.96 1.00 V 5.50 V O(uvlo) 5.50 V 110 1 + +12 % 110 ...
Page 4
... LX1 20 LX2 5 ILIM V ref N-type TEMPERATURE POWER PROTECTION FET sense FET 13 MHz OSCILLATOR 17 GND0 V ref TEA1202TS SHDWN0 V ref P-type POWER FET INTERNAL SUPPLY sense FET START-UP CIRCUIT CONTROL LOGIC CURRENT LIMIT AND COMPARATOR MODE GEARBOX TIME COUNTER SYNC DIGITAL CONTROLLER GATE ...
Page 5
... LX2 20 inductor connection 2 FUNCTIONAL DESCRIPTION Control mechanism The TEA1202TS DC/DC converter is able to operate in PFM (discontinuous conduction) or PWM (continuous conduction) operating mode. All switching actions are completely determined by a digital control circuit which uses the output voltage level as its control input. This novel ...
Page 6
... Fig.3 Response to load increase maximum typical positive spread situation Fig.4 Output voltage window spread. 6 Objective specification TEA1202TS high window limit low window limit time time MGK925 maximum negative spread MGU061 ...
Page 7
... In low output power situations, the TEA1202TS will switch over to PFM (discontinuous conduction) operating mode. In this mode, regulation information from an earlier PWM operating mode is used. This results in optimum inductor peak current levels in the PFM mode, which are slightly larger than the inductor ripple current in the PWM mode ...
Page 8
... Battery power unit External synchronization and PWM-only mode If an external high-frequency clock or a HIGH level is applied to pin SYNC/PWM, the TEA1202TS will use PWM regulation independent of the load applied. In the event a high-frequency clock is applied, the switching frequency in the PWM mode will be exactly that frequency divided by 22 ...
Page 9
... QUALITY SPECIFICATION In accordance with “SNW-FQ-611 part E” . 2000 Jun 08 CONDITIONS MIN. shut-down mode 0.2 operating mode 0 notes 1 and 2 CONDITIONS in free air 9 Objective specification TEA1202TS MAX. UNIT +6.5 V +5.5 V +150 C +80 C +125 C Class II V VALUE UNIT 140 K/W ...
Page 10
... amb 1 3 note 100 mA L PWM mode 480 6 note 6 10 Objective specification TEA1202TS MIN. TYP. MAX. UNIT 5.50 V I(start) 5.50 V O(uvlo) 0.96 1.00 V 2.2 2.4 V 5.50 V O(uvlo) 5.50 V 2.0 2.5 % 110 ...
Page 11
... LDO note 10 25 after load step from no load to I LDO(max) V > FB1 > 0.40 FB1 0 falling V bat falling V 0.88 bat Objective specification TEA1202TS MIN. TYP. MAX. UNIT 2.0 +2 ...
Page 12
... The dropout voltage is measured while the LDO input voltage is decreasing and at maximum current. 10. Measured with a sine wave at f 2000 Jun 08 CONDITIONS all blocks operating following 100 MHz 100 mV (RMS) and Objective specification TEA1202TS MIN. TYP. MAX. UNIT 1.165 1.190 1.215 V 270 A 20 +25 +80 C 150 ...
Page 13
... R7 12 OUT1 6 LBO 14 U/D FB1 19 7 TEA1202TS SYNC/PWM 18 SHDWN0 OUT2 2 10 SHDWN2 3 Vref FB2 GND GND0 13 Objective specification TEA1202TS DC/DC output regulator 1 LDO1 output regulator 2 LDO2 output low battery detection R10 DC/DC output regulator 1 output regulator 2 output MGU063 ...
Page 14
... LBI2 TEA1202TS LBO 14 7 SYNC/PWM 18 SHDWN0 2 10 SHDWN2 3 Vref GND GND0 14 Objective specification TEA1202TS DC/DC output regulator 1 LDO1 output regulator 2 LDO2 output low battery detection R10 ILIM UPOUT/DNIN DC/DC output R1 FB0 C2 R2 OUT1 regulator 1 output R3 FB1 C3 R4 OUT2 ...
Page 15
... TEA1202TS R9 U LBO 14 7 SYNC/PWM 18 SHDWN0 2 10 SHDWN2 3 Vref GND GND0 15 Objective specification TEA1202TS control regulator 1 switch DC/DC output output SWITCH regulator 1 LDO1 switch regulator 2 LDO2 output low battery detection R10 ILIM UPOUT/DNIN DC/DC output R1 FB0 C2 R2 output OUT1 regulator 1 ...
Page 16
... LBI2 12 R9 U/D 19 TEA1202TS LBO 14 SYNC/PWM 18 SHDWN0 2 10 SHDWN2 3 Vref GND GND0 16 Objective specification TEA1202TS DC/DC output regulator 1 LDO1 output regulator 2 LDO2 output low battery detection R10 ILIM 5 LX2 L1 DC/DC LX1 1 output D1 R1 FB0 C2 R2 OUT1 regulator 1 6 output ...
Page 17
... Philips Semiconductors Battery power unit External component selection I L1 NDUCTOR The performance of the TEA1202TS is not very sensitive to inductance value. The best efficiency performance over a wide load current range is achieved by using an inductance of 6.8 H e.g. TDK SLF7032 or Coilcraft DO1608 range. DC/DC C1 INPUT CAPACITOR The value of C1 strongly depends on the type of input source ...
Page 18
... R8 and R9. In that situation, capacitor C6 (10 F) must be connected between pin LBI1 and ground. The low-battery detection level for a higher battery voltage can be set by the resistors at pin LBI2 using the formula LBI2 18 Objective specification TEA1202TS R7 ------- - R9 C6 AND ...
Page 19
... 2.5 scale (1) ( 0.32 0.20 6.6 4.5 6.6 0.65 0.20 0.13 6.4 4.3 6.2 REFERENCES JEDEC EIAJ MO-152 19 Objective specification detail 0.75 0.65 1.0 0.2 0.13 0.45 0.45 EUROPEAN PROJECTION TEA1202TS SOT266 ( 0.48 10 0.1 o 0.18 0 ISSUE DATE 95-02-22 99-12-27 ...
Page 20
... Use a low voltage ( less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 C. 20 Objective specification TEA1202TS ...
Page 21
... Wave soldering is only suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65 mm definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. 2000 Jun 08 SOLDERING METHOD WAVE not suitable (2) not suitable suitable (3)(4) not recommended (5) not recommended 21 Objective specification TEA1202TS (1) REFLOW suitable suitable suitable suitable suitable ...
Page 22
... Objective specification TEA1202TS (1) These products are not Philips Semiconductors ...
Page 23
... Philips Semiconductors Battery power unit 2000 Jun 08 NOTES 23 Objective specification TEA1202TS ...
Page 24
... Tel. +46 8 5985 2000, Fax. +46 8 5985 2745 Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH, Tel. +41 1 488 2741 Fax. +41 1 488 3263 Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1, TAIPEI, Taiwan Tel. +886 2 2134 2886, Fax. +886 2 2134 2874 Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260, Tel ...