ADS7864YB Burr-Brown Corporation, ADS7864YB Datasheet - Page 10
![no-image](/images/no-image-200.jpg)
ADS7864YB
Manufacturer Part Number
ADS7864YB
Description
500kHz/ 12-Bit/ 6-Channel Simultaneous Sampling ANALOG-TO-DIGITAL CONVERTER
Manufacturer
Burr-Brown Corporation
Datasheet
1.ADS7864YB.pdf
(16 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADS7864YB
Manufacturer:
TIBB
Quantity:
362
Part Number:
ADS7864YB
Manufacturer:
TI/德州仪器
Quantity:
20 000
Company:
Part Number:
ADS7864YB/250
Manufacturer:
Texas Instruments
Quantity:
10 000
Part Number:
ADS7864YB/250
Manufacturer:
TI/德州仪器
Quantity:
20 000
Company:
Part Number:
ADS7864YB/250G4
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
ADS7864YB/2K
Manufacturer:
Texas Instruments
Quantity:
10 000
TRANSITION NOISE
Figure 5 shows a histogram plot for the ADS7864 following
8,000 conversions of a DC input. The DC input was set at
output code 2046. All but one of the conversions had an
output code result of 2046 (one of the conversions resulted
in an output of 2047). The histogram reveals the excellent
noise performance of the ADS7864.
BIPOLAR INPUTS
The differential inputs of the ADS7864 were designed to
accept bipolar inputs (–V
reference voltage (2.5V), which corresponds to a 0V to 5V
input range with a 2.5V reference. By using a simple op amp
circuit featuring a single amplifier and four external resis-
tors, the ADS7864 can be configured to except bipolar
inputs. The conventional
ranges can be interfaced to the ADS7864 using the resistor
values shown in Figure 7.
TIMING AND CONTROL
The ADS7864 uses an external clock (CLOCK, pin 22)
which controls the conversion rate of the CDAC. With an
8MHz external clock, the A/D sampling rate is 500kHz
which corresponds to a 2 s maximum throughput time.
FIGURE 5. Histogram of 8,000 Conversions of a DC Input.
FIGURE 6. Test Circuits for Timing Specifications.
DATA
8000
7000
6000
5000
4000
3000
2000
1000
Voltage Waveforms for DATA Rise and Fall Times t
0
t
R
®
2044
ADS7864
DATA
2045
REF
Code (decimal)
1.4V
and +V
2.5V,
2046
3k
100pF
C
LOAD
REF
5V, and
) around the internal
Test Point
2047
t
F
R
, and t
10V input
2048
V
V
OH
OL
F
.
10
FIGURE 7. Level Shift Circuit for Bipolar Input Ranges.
THEORY OF OPERATION
The ADS7864 contains two 12-bit A/D converters that operate
simultaneously. The three hold signals (HOLDA, HOLDB,
HOLDC) select the input MUX and initiate the conversion. A
simultaneous hold on all six channels can occur with all three
hold signals strobed together. The converted values are saved
in 6 registers. For each read operation the ADS7864 outputs
16 bits of information (12 Data, 3 Channel Address and Data
Valid). The Address/Mode signals (A0, A1, A2) select how
the data is read from the ADS7864. These Address/Mode
signals can define a selection of a single channel, a cycle mode
that cycles through all channels or a FIFO mode that se-
quences the data determined by the order of the Hold signals.
The FIFO mode will allow the 6 registers to be used by a
single channel pair and therefore three locations for CH X0
and three locations for CH X1 can be acquired before they are
read from the part.
EXPLANATION OF CLOCK, RESET
AND BUSY PINS
CLOCK—An external clock has to be provided for the
ADS7864. The maximum clock frequency is 8MHz. The
minimum clock cycle is 125ns (Figure 8, t
has to remain HIGH (Figure 8, t
at least 40ns.
RESET—Bringing reset LOW will reset the ADS7864. It
will clear all the output registers, stop any actual conversions
and will close the sampling switches. Reset has to stay LOW
for at least 20ns (Figure 8, t
HIGH for at least 20ns (Figure 8, t
conversion (negative hold edge).
BUSY—Busy goes LOW when the internal A/D converters
start a new conversion. It stays LOW as long as the conver-
sion is in progress (Figure 9, 13 clock-cycles, t
again, after the data is latched to the output register. With
busy going high, the new data can be read. It takes at least
16 clock cycles (Figure 9, t
Bipolar Input
BIPOLAR INPUT
2.5V
10V
5V
20k
4k
1k
2k
4k
R
1
R
2
OPA340
11
R
) to complete conversion.
8
10k
20k
1
5k
). The reset should be back
R
6
2
) or LOW (Figure 8, t
9
), before starting the next
5
+IN
–IN
REF
2.5V
), and the clock
ADS7864
OUT
10
) and rises
(pin 33)
7
) for