MCRF200 Microchip Technology Inc., MCRF200 Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/4/440/microchip_technology_inc__sml.jpg)
MCRF200
Manufacturer Part Number
MCRF200
Description
125 Khz Microid? Passive Rfid Device
Manufacturer
Microchip Technology Inc.
Datasheet
1.MCRF200.pdf
(24 pages)
2.2
The configuration register determines the operational
parameters of the device. The configuration register
can
programmed during wafer probe at the Microchip
factory. CB11 is always a zero; CB12 is set when
successful contact or contactless programming of the
data array has been completed. Once CB12 is set,
device programming and erasing is disabled. Table 2-4
contains a description of the bit functions of the control
register.
2.2.1
The chip will access data at a baud rate determined by
bits CB2, CB3 and CB4 of the configuration register.
For example, MOD32 (CB2 = 0, CB3 = 1, CB4 = 1) has
32 RF cycles per bit. This gives the data rate of 4 kHz
for the RF carrier frequency of 128 kHz.
The default timing is MOD128 (F
mode is used for contact and contactless program-
ming. Once the array is successfully programmed, the
lock bit CB12 is set. When the lock bit is set, program-
ming and erasing the device becomes permanently
disabled. The configuration register has no effect on
device timing until the EEPROM data array is
programmed (CB12 = 1).
2.2.2
This logic acts upon the serial data being read from the
EEPROM. The logic encodes the data according to the
configuration bits CB6 and CB7. CB6 and CB7
determine the data encoding method. The available
choices are:
• Non-return to zero-level (NRZ_L)
• Biphase Differential, Biphase Manchester
• Inverted Manchester
FIGURE 2-2:
¤ 2003 Microchip Technology Inc.
not
5 cycles (HI)
Configuration Register and
Control Logic
BAUD RATE TIMING OPTION
DATA ENCODING OPTION
be
5 cycles (LO)
programmed
Encoded Data ‘1’
ENCODED DATA AND FSK OUTPUT SIGNAL FOR MOD40 OPTION
40 RF cycles
contactlessly;
CLK
/128), and this
it
is
4 cycles (HI)
4 cycles (LO)
2.2.3
CB8 and CB9 determine the modulation protocol of the
encoded data. The available choices are:
• ASK
• FSK
• PSK_1
• PSK_2
When ASK (direct) option is chosen, the encoded data
is fed into the modulation transistor without change.
When FSK option is chosen, the encoded data is
represented by:
a)
b)
For example, FSK signal for MOD40 is represented:
a)
b)
Refer to Figure 2-2 for the FSK signal with MOD40
option.
The PSK_1 represents change in the phase of the
modulation signal at the change of the encoded data.
For example, the phase changes when the encoded
data is changed from ‘1’ to ‘0’, or from ‘0’ to ‘1’.
The PSK_2 represents change in the phase at the
change on ‘1’. For example, the phase changes when
the encoded data is changed from ‘0’ to ‘1’, or from ‘1’
to ‘1’.
Encoded Data ‘0’
Sets of 10 RF carrier cycles (first 5 cycles
higher amplitude, the last 5 cycles
amplitude) for logic “high” level.
Sets of 8 RF carrier cycles (first 4 cycles
higher amplitude, the last 4 cycles
amplitude) for logic “low” level.
4 sets of 10 RF carrier cycles for data ‘1’.
5 sets of 8 RF carrier cycles for data ‘0’.
40 RF cycles
MODULATION OPTION
MCRF200
DS21219H-page 5
lower
lower