ST92150CV1Q-Auto STMicroelectronics, ST92150CV1Q-Auto Datasheet - Page 379

• Manufacturer Part Number: ST92150CV1Q-Auto
• Description: 8-bit MCU for automotive
• Manufacturer: STMicroelectronics

Specifications of ST92150CV1Q-Auto

• Internal Memory: Single Voltage FLASH up to 256 Kbytes, RAM up to 8Kbytes, 1K byte E3 TM (Emulated EEPROM)
• Minimum Instruction Time: 83 ns (24 MHz int. clock)

AC ELECTRICAL CHARACTERISTICS
(V
ified)
Note:
All I/O Ports are configured in bidirectional weak pull-up mode with no DC load, unless otherwise specified, external clock is driven by a
square wave.
(1) Unless otherwise stated, typical data are based on V
(2) Current consumption to be added to IDD
(3) Value guaranteed by product characterization, not tested in production.
(4) Current consumption to be added to IDD
(5) The I/Os draw a transient current from V
or V
Symbol
I
I
I
DDLPWFI
I
I
I
DDSTOP
DD
I
I
DDHALT
DDRUN
∆I
∆I
∆I
DDOSC
DDRTC
I
DDLPR
DDWFI
DDTR
IN
DD1
DD2
DD3
>V
= 5 V ± 10%, T
DD
-0.3V, it typically reaches its maximum value when V
Run Mode Current
FLASH/E
Supply Current
(Read)
FLASH/E
Supply Current
(Write/Erase)
Typical application
Run Mode Current
WFI Mode Current
FLASH/E
Supply Current
(Stand-by)
Main Voltage Regu-
lator Power
Consumption
Crystal Oscillator
Power Consump-
tion
Low Power WFI
Mode Current
RTC Mode Current
HALT Mode Cur-
rent
STOP Mode Cur-
rent
Input Transient I
Current
Parameter
(3)
(3)
(2)
(5)
3 TM
3 TM
3 TM
(4)
A
=
(2)
–
DD
40° C to +125° C for Max values and 25°C for Typ values, unless otherwise spec-
CPU running with code execution
from RAM memory, all peripherals
in reset state, clock input (OSCIN)
driven by external square wave.
f
CPU running with code execution
from FLASH memory, all peripher-
als running in a typical configura-
tion, clock input (OSCIN) driven by
a 4-MHz crystal =
I
(Timers, CAN, etc)
FLASH/E
Main Voltage Regulator ON, I
PR
real time clock mode)
FLASH/E
Mode, Main Voltage Regulator
OFF, Standard Timer in Real Time
Clock mode
All I/O ports are configured in out-
put push-pull mode with no DC
load
DDRUN
f
INTCLK
INTCLK
+ I
DDOSC
RUN
LPWFI
DD
+ ∆I
in [MHz].
in [MHz].
3 TM
3 TM
when an input takes a voltage level in between V
Conditions
when the FLASH memory is accessed.
DD1
when the FLASH memory is in stand-by mode.
+ I
in Stand-by Mode,
in Power-Down
DD (Standard Timer in
+ I
DD Peripherals
DD
= 5V. They are only reported for design guide lines not tested in production.
ST92124xxx-Auto/150xxxxx-Auto/250xxxx-Auto
IN
is approximatively at V
DDL-
4MHz / 32
4MHz / 32
frequency
frequency
INTCLK
24 MHz
24 MHz
24 MHz
any
any
-
-
-
-
-
-
DD
see
1.8xf
/2.
Figure 159
Typ
INTCLK
2.5 +
300
200
550
250
300
SS
12
20
45
50
14
2
5
and V
(1)
/MHz
(3)
DD
. This current is 0 for V
0.9xf
INTCLK
Max
1000
60
22
25
/MHz
(3)
379/430
IN
<0.3V
Unit
mA
mA
mA
mA
mA
mA
mA
µA
µA
µA
µA
µA
µA
µA
µA
1