ST72215G2 STMicroelectronics, ST72215G2 Datasheet - Page 62
ST72215G2
Manufacturer Part Number
ST72215G2
Description
8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY,ADC, 16-BIT TIMERS, SPI, I2C INTERFACES
Manufacturer
STMicroelectronics
Datasheet
1.ST72104G2.pdf
(141 pages)
Specifications of ST72215G2
Emulation Voltage
5.5 V
- Current page: 62 of 141
- Download datasheet (3Mb)
ST72104Gx, ST72215Gx, ST72216Gx, ST72254Gx
SERIAL PERIPHERAL INTERFACE (Cont’d)
11.3.4 Functional Description
Figure 1
(SPI) block diagram.
This interface contains three dedicated registers:
Refer to the CR, SR and DR registers in
0.1.7
11.3.4.1 Master Configuration
In a master configuration, the serial clock is gener-
ated on the SCK pin.
Procedure
62/141
– A Control Register (CR)
– A Status Register (SR)
– A Data Register (DR)
– Select the SPR0 & SPR1 bits to define the se-
– Select the CPOL and CPHA bits to define one
– The SS pin must be connected to a high level
– The MSTR and SPE bits must be set (they re-
rial clock baud rate (see CR register).
of the four relationships between the data
transfer and the serial clock (see
signal during the complete byte transmit se-
quence.
main set only if the SS pin is connected to a
high level signal).
for the bit definitions.
shows the serial peripheral interface
Figure
Section
4).
In this configuration the MOSI pin is a data output
and to the MISO pin is a data input.
Transmit sequence
The transmit sequence begins when a byte is writ-
ten the DR register.
The data byte is parallel loaded into the 8-bit shift
register (from the internal bus) during a write cycle
and then shifted out serially to the MOSI pin most
significant bit first.
When data transfer is complete:
During the last clock cycle the SPIF bit is set, a
copy of the data byte received in the shift register
is moved to a buffer. When the DR register is read,
the SPI peripheral returns this buffered value.
Clearing the SPIF bit is performed by the following
software sequence:
1. An access to the SR register while the SPIF bit
2. A read to the DR register.
Note: While the SPIF bit is set, all writes to the DR
register are inhibited until the SR register is read.
– The SPIF bit is set by hardware
– An interrupt is generated if the SPIE bit is set
is set
and the I bit in the CCR register is cleared.
Related parts for ST72215G2
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet: