ST72324K4 STMicroelectronics, ST72324K4 Datasheet - Page 43

• Manufacturer Part Number: ST72324K4
• Description: 8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, 4 TIMERS, SPI, SCI INTERFACE
• Manufacturer: STMicroelectronics

Specifications of ST72324K4

• Hdflash Endurance: 100 cycles, data retention
• Clock Sources: crystal/ceramic resonator oscillators, internal RC oscillator, clock security system and bypass for external clock
• Four Power Saving Modes: Halt, Active-Halt, Wait and Slow
• Main Clock Controller With: Real time base, Beep and Clock-out capabilities
• 16-bit Timer A With: 1 input capture, 1 output compare, external clock input, PWM and pulse generator modes
• 16-bit Timer B With: 2 input captures, 2 output compares, PWM and pulse generator modes

POWER SAVING MODES (Cont’d)
8.4.2 HALT MODE
The HALT mode is the lowest power consumption
mode of the MCU. It is entered by executing the
‘HALT’ instruction when the OIE bit of the Main
Clock Controller Status register (MCCSR) is
cleared (see
tails on the MCCSR register).
The MCU can exit HALT mode on reception of ei-
ther a specific interrupt (see
Mapping,” on page
HALT mode by means of a RESET or an interrupt,
the oscillator is immediately turned on and the 256
or 4096 CPU cycle delay is used to stabilize the
oscillator. After the start up delay, the CPU
resumes operation by servicing the interrupt or by
fetching the reset vector which woke it up (see
ure
When entering HALT mode, the I[1:0] bits in the
CC register are forced to ‘10b’to enable interrupts.
Therefore, if an interrupt is pending, the MCU
wakes up immediately.
In HALT mode, the main oscillator is turned off
causing all internal processing to be stopped, in-
cluding the operation of the on-chip peripherals.
All peripherals are not clocked except the ones
which get their clock supply from another clock
generator (such as an external or auxiliary oscilla-
tor).
The compatibility of Watchdog operation with
HALT mode is configured by the “WDGHALT” op-
tion bit of the option byte. The HALT instruction
when executed while the Watchdog system is en-
abled, can generate a Watchdog RESET (see
Section 14.1 on page
Figure 27. HALT Timing Overview
[MCCSR.OIE=0]
INSTRUCTION
RUN
28).
HALT
HALT
Section 10.2 on page 56
256 OR 4096 CPU
36) or a RESET. When exiting
CYCLE DELAY
INTERRUPT
150) for more details.
RESET
OR
Table 8, “Interrupt
VECTOR
FETCH
for more de-
RUN
Fig-
Figure 28. HALT Mode Flow-chart
Notes:
1. WDGHALT is an option bit. See option byte sec-
tion for more details.
2. Peripheral clocked with an external clock source
can still be active.
3. Only some specific interrupts can exit the MCU
from HALT mode (such as external interrupt). Re-
fer to
more details.
4. Before servicing an interrupt, the CC register is
pushed on the stack. The I[1:0] bits of the CC reg-
ister are set to the current software priority level of
the interrupt routine and recovered when the CC
register is popped.
N
HALT INSTRUCTION
WATCHDOG
WDGHALT
Table 8, “Interrupt Mapping,” on page 36
(MCCSR.OIE=0)
RESET
1
INTERRUPT
Y
1)
3)
ENABLE
ST72324Jx ST72324Kx
256 OR 4096 CPU CLOCK
OR SERVICE INTERRUPT
0
FETCH RESET VECTOR
OSCILLATOR
PERIPHERALS
CPU
I[1:0] BITS
OSCILLATOR
PERIPHERALS
CPU
I[1:0] BITS
OSCILLATOR
PERIPHERALS
CPU
I[1:0] BITS
N
CYCLE
RESET
Y
WATCHDOG
DELAY
DISABLE
2)
XX
XX
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
10
43/164
4)
4)
for
1