MPT612 NXP Semiconductors, MPT612 Datasheet - Page 19

• Manufacturer Part Number: MPT612
• Description: The MPT612, the first dedicated IC for performing the Maximum Power Point Tracking (MPPT) function, is designed for use in applications that use solar photovoltaic (PV) cells or in fuel cells
• Manufacturer: NXP Semiconductors

NXP Semiconductors
8. Limiting values
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10] Dependent on package type
MPT612
Product data sheet
Symbol
V
V
V
V
V
V
I
I
T
P
V
Table 3. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
DD
SS
stg
DDC
DD(IO)
DD(ADC)
DD(RTC)
IA
I
tot(pack)
ESD
The following applies to the limiting values:
a) This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive
b) Core and internal rail
External rail
On ADC related pins
Including voltage on outputs in 3-state mode
Only valid when the V
Not to exceed 4.6 V
Per supply pin
The peak current is limited to 25 times the corresponding maximum current
Per ground pin
static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated
maximum. Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to GND
unless otherwise noted.
7.17.11 RealMonitor
Parameter
core supply voltage
input/output supply voltage
ADC supply voltage
RTC supply voltage
analog input voltage
input voltage
supply current
ground current
storage temperature
total power dissipation (per
package)
electrostatic discharge voltage
DD(IO)
port to be used for sending and receiving data without affecting the normal program flow.
The debug communication channel data and control registers are mapped in to
addresses in the EmbeddedICE logic. The JTAG clock (TCK) must be slower than
the CPU clock (CCLK) to enable the JTAG interface to operate.
RealMonitor is a configurable software module, developed by ARM Inc. which enables
real time debugging. It is a lightweight debug monitor that runs in the background while
users debug the foreground application. It communicates with the host using DCC which
is present in the EmbeddedICE logic. The MPT612 contain a specific configuration of
RealMonitor software programmed into the on-chip boot ROM memory.
supply voltage is present
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 14 September 2010
Conditions
typical: 1.8 V
typical: 3.3 V
pad supply: 3.3 V
5 V tolerant I/O pins
other I/O pins
based on package heat
transfer, not device power
consumption
Human Body Model (HBM)
Machine Model (MM)
Charged Device Model (CDM)
[1]
Maximum power point tracking IC
[4][5]
[4][5]
[1]b)
[[11]
[10]
[12]
[13]
[2]
[3]
[7]
[9]
Min
−0.5
−0.5
−0.5
−0.5
−0.5
−0.5
−0.5
-
-
−65
-
−4000
−200
−800
Max
+2.5
+4.6
+4.6
+4.6
+5.1
+6.0
V
100
100
+150
1.5
+4000
+200
+800
DD(IO)
© NXP B.V. 2010. All rights reserved.
[8]
[8]
MPT612
+ 0.5
[6]
19 of 19
1
/
6
Unit
V
V
V
V
V
V
V
mA
mA
°C
W
V
V
V
of