P89LPC930_931 NXP Semiconductors, P89LPC930_931 Datasheet - Page 22
![The P89LPC930/931 are single-chip microcontrollers designed for applicationsdemanding high-integration, low cost solutions over a wide range of performancerequirements](/photos/41/52/415285/sot361-1_3d_sml.gif)
P89LPC930_931
Manufacturer Part Number
P89LPC930_931
Description
The P89LPC930/931 are single-chip microcontrollers designed for applicationsdemanding high-integration, low cost solutions over a wide range of performancerequirements
Manufacturer
NXP Semiconductors
Datasheet
1.P89LPC930_931.pdf
(55 pages)
Philips Semiconductors
9397 750 14472
Product data
8.11.1 Port configurations
8.11.2 Quasi-bidirectional output configuration
8.11.3 Open-drain output configuration
8.11.4 Input-only configuration
8.11.5 Push-pull output configuration
8.11.6 Port 0 analog functions
All but three I/O port pins on the P89LPC930/931 may be configured by software to
one of four types on a bit-by-bit basis. These are: quasi-bidirectional (standard 80C51
port outputs), push-pull, open drain, and input-only. Two configuration registers for
each port select the output type for each port pin.
P1.5 (RST) can only be an input and cannot be configured.
P1.2 (SCL/T0) and P1.3 (SDA/INT0) may only be configured to be either input-only or
open-drain.
Quasi-bidirectional outputs can be used as both an input and output without the need
to reconfigure the port. This is possible because when the port outputs a logic HIGH,
it is weakly driven, allowing an external device to pull the pin LOW. When the pin is
driven LOW, it is driven strongly and able to sink a fairly large current. These features
are somewhat similar to an open-drain output except that there are three pull-up
transistors in the quasi-bidirectional output that serve different purposes.
The P89LPC930/931 is a 3 V device, but the pins are 5 V-tolerant. In
quasi-bidirectional mode, if a user applies 5 V on the pin, there will be a current
flowing from the pin to V
5 V in quasi-bidirectional mode is discouraged.
A quasi-bidirectional port pin has a Schmitt-triggered input that also has a glitch
suppression circuit.
The open-drain output configuration turns off all pull-ups and only drives the
pull-down transistor of the port driver when the port latch contains a logic ‘0’. To be
used as a logic output, a port configured in this manner must have an external
pull-up, typically a resistor tied to V
An open-drain port pin has a Schmitt-triggered input that also has a glitch
suppression circuit.
The input-only port configuration has no output drivers. It is a Schmitt-triggered input
that also has a glitch suppression circuit.
The push-pull output configuration has the same pull-down structure as both the
open-drain and the quasi-bidirectional output modes, but provides a continuous
strong pull-up when the port latch contains a logic ‘1’. The push-pull mode may be
used when more source current is needed from a port output. A push-pull port pin
has a Schmitt-triggered input that also has a glitch suppression circuit.
The P89LPC930/931 incorporates two Analog Comparators. In order to give the best
analog function performance and to minimize power consumption, pins that are being
used for analog functions must have the digital outputs and digital inputs disabled.
Rev. 05 — 15 December 2004
DD
, causing extra power consumption. Therefore, applying
8-bit microcontrollers with two-clock 80C51 core
DD
.
P89LPC930/931
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
22 of 55