SAM3S8C Atmel Corporation, SAM3S8C Datasheet - Page 16
SAM3S8C
Manufacturer Part Number
SAM3S8C
Description
Manufacturer
Atmel Corporation
- Current page: 16 of 1143
- Download datasheet (20Mb)
5. Power Considerations
5.1
5.2
5.3
16
Power Supplies
Voltage Regulator
Typical Powering Schematics
SAM3S8/SD8
The SAM3S8/SD8 has several types of power supply pins:
The SAM3S8/SD8 embeds a voltage regulator that is managed by the Supply Controller.
This internal regulator is designed to supply the internal core of SAM3S8/SD8. It features two
operating modes:
For adequate input and output power supply decoupling/bypassing, refer to the “Voltage Regula-
tor” section in the “Electrical Characteristics” section of the datasheet.
The SAM3S8/SD8 supports a 1.62V-3.6V single supply mode. The internal regulator input is
connected to the source and its output feeds VDDCORE.
schematics.
As VDDIN powers the voltage regulator, the ADC, DAC and the analog comparator, when the
user does not want to use the embedded voltage regulator, it can be disabled by software via
the SUPC (note that this is different from Backup mode).
• VDDCORE pins: Power the core, the embedded memories and the peripherals. Voltage
• VDDIO pins: Power the Peripherals I/O lines (Input/Output Buffers), USB transceiver, Backup
• VDDIN pin: Voltage Regulator Input, ADC, DAC and Analog Comparator Power Supply.
• VDDPLL pin: Powers the PLLA, PLLB, the Fast RC and the 3 to 20 MHz oscillator. Voltage
• In Normal mode, the voltage regulator consumes less than 700 µA static current and draws
• In Backup mode, the voltage regulator consumes less than 1 µA while its output (VDDOUT)
ranges from 1.62V to 1.95V.
part, 32 kHz crystal oscillator and oscillator pads. Voltage ranges from 1.62V to 3.6V.
Voltage ranges from 1.8V to 3.6V.
ranges from 1.62V to 1.95V.
80 mA of output current. Internal adaptive biasing adjusts the regulator quiescent current
depending on the required load current. In Wait Mode quiescent current is only 7 µA.
is driven internally to GND. The default output voltage is 1.80V and the start-up time to reach
Normal mode is less than 100 µs.
Figure 5-1
below shows the power
11090A–ATARM–10-Feb-12
Related parts for SAM3S8C
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
ARM-based Flash MCU
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: