SAM9R64 Atmel Corporation, SAM9R64 Datasheet - Page 401
SAM9R64
Manufacturer Part Number
SAM9R64
Description
Manufacturer
Atmel Corporation
Datasheets
1.M40800.pdf
(284 pages)
2.SAM9260.pdf
(290 pages)
3.SAM9261.pdf
(248 pages)
4.SAM9R64.pdf
(903 pages)
5.SAM9R64.pdf
(52 pages)
Specifications of SAM9R64
Flash (kbytes)
0 Kbytes
Pin Count
144
Max. Operating Frequency
240 MHz
Cpu
ARM926
Hardware Qtouch Acquisition
No
Max I/o Pins
49
Ext Interrupts
49
Usb Transceiver
1
Usb Speed
Hi-Speed
Usb Interface
Device
Spi
1
Twi (i2c)
1
Uart
5
Ssc
1
Sd / Emmc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
3
Adc Resolution (bits)
10
Adc Speed (ksps)
220
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
64
Self Program Memory
NO
External Bus Interface
1
Dram Memory
sdram
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
1.08 to 1.32
Fpu
No
Mpu / Mmu
No / Yes
Timers
3
Output Compare Channels
3
Input Capture Channels
3
Pwm Channels
3
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- M40800 PDF datasheet
- SAM9260 PDF datasheet #2
- SAM9261 PDF datasheet #3
- SAM9R64 PDF datasheet #4
- SAM9R64 PDF datasheet #5
- Current page: 401 of 903
- Download datasheet (13Mb)
33.4
Figure 33-2. Application Block Diagram
33.4.1
Table 33-3.
33.5
33.5.1
33.5.2
33.5.3
401
Pin Name
TWD
TWCK
Application Block Diagram
Product Dependencies
AT91SAM9R64/RL64
I/O Lines Description
I/O Lines
Power Management
Interrupt
I/O Lines Description
Rp: Pull up value as given by the I
Host with
Interface
TWI
Both TWD and TWCK are bidirectional lines, connected to a positive supply voltage via a current
source or pull-up resistor (see
high. The output stages of devices connected to the bus must have an open-drain or open-col-
lector to perform the wired-AND function.
TWD and TWCK pins may be multiplexed with PIO lines. To enable the TWI, the programmer
must perform the following steps:
The TWI interface may be clocked through the Power Management Controller (PMC), thus the
programmer must first configure the PMC to enable the TWI clock.
The TWI interface has an interrupt line connected to the Advanced Interrupt Controller (AIC). In
order to handle interrupts, the AIC must be programmed before configuring the TWI.
TWD
TWCK
• Program the PIO controller to:
• Enable the peripheral clock.
– Dedicate TWD and TWCK as peripheral lines.
– Define TWD and TWCK as open-drain.
Serial EEPROM
Pin Description
Two-wire Serial Data
Two-wire Serial Clock
Atmel TWI
Slave 1
2
C Standard
I
Slave 2
2
C RTC
Figure 33-2 on page
Controller
I
2
Slave 3
C LCD
I
2
401). When the bus is free, both lines are
Slave 4
Sensor
C Temp.
Rp
Rp
Input/Output
Input/Output
VDD
6289D–ATARM–3-Oct-11
Type
Related parts for SAM9R64
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: