SAM7S16 Atmel Corporation, SAM7S16 Datasheet - Page 69
SAM7S16
Manufacturer Part Number
SAM7S16
Description
Manufacturer
Atmel Corporation
Specifications of SAM7S16
Flash (kbytes)
16 Kbytes
Pin Count
48
Max. Operating Frequency
55 MHz
Cpu
ARM7TDMI
Hardware Qtouch Acquisition
No
Max I/o Pins
21
Ext Interrupts
21
Usb Speed
No
Usb Interface
No
Spi
1
Twi (i2c)
1
Uart
2
Ssc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
384
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
4
Self Program Memory
NO
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
3.0 to 3.6
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
3
Input Capture Channels
3
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- Current page: 69 of 284
- Download datasheet (2Mb)
2.9
2.9.1
2.9.2
ARM DDI 0029G
Interrupt latencies
Maximum interrupt latencies
Minimum interrupt latencies
The calculations for maximum and minimum latency are described in:
•
•
When FIQs are enabled, the worst-case latency for FIQ comprises a combination of:
•
•
•
•
The total latency is therefore 29 processor cycles, just over 0.7 microseconds in a
system that uses a continuous 40MHz processor clock. At the end of this time, the
ARM7TDMI processor executes the instruction at
The maximum IRQ latency calculation is similar, but must allow for the fact that FIQ,
having higher priority, can delay entry into the IRQ handling routine for an arbitrary
length of time.
The minimum latency for FIQ or IRQ is the shortest time the request can take through
the synchronizer, T
Maximum interrupt latencies on page 2-23
Minimum interrupt latencies on page 2-23.
The longest time the request can take to pass through the synchronizer, T
(four processor cycles).
The time for the longest instruction to complete, T
an LDM which loads all the registers including the PC. T
wait state system.
The time for the Data Abort entry, T
The time for FIQ entry, T
Copyright © 1994-2001. All rights reserved.
syncmin
, plus T
fiq
fiq
(two cycles).
, a total of five processor cycles.
exc
(three cycles).
.
ldm
. The longest instruction, is
ldm
is 20 cycles in a zero
Programmer’s Model
syncmax
2-23
Related parts for SAM7S16
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: