ATxmega32D4 Atmel Corporation, ATxmega32D4 Datasheet - Page 91
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATxmega32D4
Manufacturer Part Number
ATxmega32D4
Description
Manufacturer
Atmel Corporation
Specifications of ATxmega32D4
Flash (kbytes)
32 Kbytes
Pin Count
44
Max. Operating Frequency
32 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
34
Ext Interrupts
34
Usb Speed
No
Usb Interface
No
Spi
4
Twi (i2c)
2
Uart
2
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
12
Adc Resolution (bits)
12
Adc Speed (ksps)
200
Analog Comparators
2
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
4
Eeprom (bytes)
1024
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.6 to 3.6
Operating Voltage (vcc)
1.6 to 3.6
Fpu
No
Mpu / Mmu
no / no
Timers
4
Output Compare Channels
14
Input Capture Channels
14
Pwm Channels
14
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATxmega32D4-AU
Manufacturer:
Atmel
Quantity:
123
Part Number:
ATxmega32D4-AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATxmega32D4-CU
Manufacturer:
Maxim
Quantity:
71
Company:
Part Number:
ATxmega32D4-MH
Manufacturer:
Atmel
Quantity:
1 910
Company:
Part Number:
ATxmega32D4-MH
Manufacturer:
Atmel
Quantity:
1 704
Part Number:
ATxmega32D4-MH
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
8135J–AVR–12/10
Figure 33-1. Analog Comparator Voltage Scaler vs. Scalefac
3. ADC gain stage cannot be used for single conversion
4.
5. ADC gain stage output range is limited to 2.4 V
Problem fix/Workaround
Use external voltage input for the analog comparator if accurate voltage levels are needed
The ADC gain stage will not output correct result for single conversion that is triggered and
started from software or event system.
Problem fix/Workaround
When the gain stage is used, the ADC must be set in free running mode for correct results.
ADC has increased INL error for some operating conditions
Some ADC configurations or operating condition will result in increased INL error.
In signed mode INL is increased to:
– 6LSB for sample rates above 130ksps, and up to 8LSB for 200ksps sample rate.
– 6LSB for reference voltage below 1.1V when VCC is above 3.0V.
– 20LSB for ambient temperature below 0 degree C and reference voltage below 1.3V.
In unsigned mode, the INL error cannot be guaranteed, and this mode should not be used.
Problem fix/Workaround
None, avoid using the ADC in the above configurations in order to prevent increased INL
error. Use the ADC in signed mode also for single ended measurements.
The amplified output of the ADC gain stage will never go above 2.4 V, hence the differential
input will only give correct output when below 2.4 V/gain. For the available gain settings, this
gives a differential input range of:
3.5
2.5
1.5
0.5
3
2
1
0
0
T = 25°C
5
10
15
20
25
SCALEFAC
30
35
40
45
50
55
XMEGA D4
60
65
3.3 V
2.7 V
1.8 V
91