ATxmega128A1 Atmel Corporation, ATxmega128A1 Datasheet - Page 98

• Manufacturer Part Number: ATxmega128A1
• Manufacturer: Atmel Corporation

Specifications of ATxmega128A1

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 78
• Ext Interrupts: 78
• Usb Speed: No
• Usb Interface: No
• Spi: 12
• Twi (i2c): 4
• Uart: 8
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 8
• Eeprom (bytes): 2048
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 8
• Output Compare Channels: 24
• Input Capture Channels: 24
• Pwm Channels: 24
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8067M–AVR–09/10
39. Clearing TWI Stop Interrupt Flag may lock the bus
40. TWI START condition at bus timeout will cause transaction to be dropped
41. TWI Data Interrupt Flag erroneously read as set
Problem fix/Workaround
Clear the flag in software after address interrupt.
If software clears the STOP Interrupt Flag (APIF) on the same Peripheral Clock cycle as the
hardware sets this flag due to a new address received, CLKHOLD is not cleared and the
SCL line is not released. This will lock the bus.
Problem fix/Workaround
Check if the bus state is IDLE. If this is the case, it is safe to clear APIF. If the bus state is
not IDLE, wait for the SCL pin to be low before clearing APIF.
Code:
/* Only clear the interrupt flag if within a "safe zone". */
while ( /* Bus not IDLE: */
{
}
/* Check for an pending address match interrupt */
if ( !(COMMS_TWI.SLAVE.STATUS & TWI_SLAVE_CLKHOLD_bm) )
{
}
If Bus Timeout is enabled and a timeout occurs on the same Peripheral Clock cycle as a
START is detected, the transaction will be dropped.
Problem fix/Workaround
None.
When issuing the TWI slave response command CMD=0b11, it takes 1 Peripheral Clock
cycle to clear the data interrupt flag (DIF). A read of DIF directly after issuing the command
will show the DIF still set.
Problem fix/Workaround
Add one NOP instruction before checking DIF.
/* Ensure that the SCL line is low */
if ( !(COMMS_PORT.IN & PIN1_bm) )
/* Safely clear interrupt flag */
COMMS_TWI.SLAVE.STATUS |= (uint8_t)TWI_SLAVE_APIF_bm;
)
((COMMS_TWI.MASTER.STATUS & TWI_MASTER_BUSSTATE_gm) !=
if ( !(COMMS_PORT.IN & PIN1_bm) )
TWI_MASTER_BUSSTATE_IDLE_gc)) &&
/* SCL not held by slave: */
!(COMMS_TWI.SLAVE.STATUS & TWI_SLAVE_CLKHOLD_bm)
break;
XMEGA A1
98