ATUC128L4U Atmel Corporation, ATUC128L4U Datasheet - Page 86
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATUC128L4U
Manufacturer Part Number
ATUC128L4U
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT32UC3A0128.pdf
(377 pages)
2.AT32UC3A0128.pdf
(159 pages)
3.ATUC128L4U.pdf
(960 pages)
4.ATUC128L4U.pdf
(92 pages)
Specifications of ATUC128L4U
Flash (kbytes)
128 Kbytes
Pin Count
48
Max. Operating Frequency
50 MHz
Cpu
32-bit AVR
# Of Touch Channels
17
Hardware Qtouch Acquisition
Yes
Max I/o Pins
36
Ext Interrupts
36
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
1
Twi (i2c)
2
Uart
4
Lin
4
Ssc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
12
Adc Speed (ksps)
460
Analog Comparators
8
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
16
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.62 to 3.6
Operating Voltage (vcc)
1.62 to 3.6
Fpu
No
Mpu / Mmu
Yes / No
Timers
6
Output Compare Channels
18
Input Capture Channels
12
Pwm Channels
35
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATUC128L4U-U
Manufacturer:
ATMEL
Quantity:
3 006
10.3.9
10.3.10
10.3.11
10.3.12
32142AS–12/2011
PWMA
TC
ADCIFB
CAT
5. TWIM TWALM polarity is wrong
1. The SR.READY bit cannot be cleared by writing to SCR.READY
1. Channel chaining skips first pulse for upper channel
1. ADCIFB DMA transfer does not work with divided PBA clock
1. CAT QMatrix sense capacitors discharged prematurely
When the TWIS stretches TWCK due to a slave address match, it also holds TWD low for
the same duration if it is to be receiving data. When TWIS releases TWCK, it releases TWD
at the same time. This can cause a TWI timing violation.
Fix/Workaround
None.
The TWALM signal in the TWIM is active high instead of active low.
Fix/Workaround
Use an external inverter to invert the signal going into the TWIM. When using both TWIM
and TWIS on the same pins, the TWALM cannot be used.
The Ready bit in the Status Register will not be cleared when writing a one to the corre-
sponding bit in the Status Clear register. The Ready bit will be cleared when the Busy bit is
set.
Fix/Workaround
Disable the Ready interrupt in the interrupt handler when receiving the interrupt. When an
operation that triggers the Busy/Ready bit is started, wait until the ready bit is low in the Sta-
tus Register before enabling the interrupt.
When chaining two channels using the Block Mode Register, the first pulse of the clock
between the channels is skipped.
Fix/Workaround
Configure the lower channel with RA = 0x1 and RC = 0x2 to produce a dummy clock cycle
for the upper channel. After the dummy cycle has been generated, indicated by the
SR.CPCS bit, reconfigure the RA and RC registers for the lower channel with the real
values.
DMA requests from the ADCIFB will not be performed when the PBA clock is slower than
the HSB clock.
Fix/Workaround
Do not use divided PBA clock when the PDCA transfers from the ADCIFB.
At the end of a QMatrix burst charging sequence that uses different burst count values for
different Y lines, the Y lines may be incorrectly grounded for up to n-1 periods of the periph-
eral bus clock, where n is the ratio of the PB clock frequency to the GCLK_CAT frequency.
This results in premature loss of charge from the sense capacitors and thus increased vari-
ability of the acquired count values.
Fix/Workaround
Enable the 1kOhm drive resistors on all implemented QMatrix Y lines (CSA 1, 3, 5, 7, 9, 11,
13, and/or 15) by writing ones to the corresponding odd bits of the CSARES register.
ATUC64/128/256L3/4U
86