ATUC128L4U Atmel Corporation, ATUC128L4U Datasheet - Page 81
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATUC128L4U
Manufacturer Part Number
ATUC128L4U
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT32UC3A0128.pdf
(377 pages)
2.AT32UC3A0128.pdf
(159 pages)
3.ATUC128L4U.pdf
(960 pages)
4.ATUC128L4U.pdf
(92 pages)
Specifications of ATUC128L4U
Flash (kbytes)
128 Kbytes
Pin Count
48
Max. Operating Frequency
50 MHz
Cpu
32-bit AVR
# Of Touch Channels
17
Hardware Qtouch Acquisition
Yes
Max I/o Pins
36
Ext Interrupts
36
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
1
Twi (i2c)
2
Uart
4
Lin
4
Ssc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
12
Adc Speed (ksps)
460
Analog Comparators
8
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
16
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.62 to 3.6
Operating Voltage (vcc)
1.62 to 3.6
Fpu
No
Mpu / Mmu
Yes / No
Timers
6
Output Compare Channels
18
Input Capture Channels
12
Pwm Channels
35
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATUC128L4U-U
Manufacturer:
ATMEL
Quantity:
3 006
10.2.7
10.2.8
32142AS–12/2011
CAT
aWire
1. CAT QMatrix sense capacitors discharged prematurely
2. Autonomous CAT acquisition must be longer than AST source clock period
3. CAT consumes unnecessary power when disabled or when autonomous touch not
1. aWire MEMORY_SPEED_REQUEST command does not return correct CV
Configure the lower channel with RA = 0x1 and RC = 0x2 to produce a dummy clock cycle
for the upper channel. After the dummy cycle has been generated, indicated by the
SR.CPCS bit, reconfigure the RA and RC registers for the lower channel with the real
values.
At the end of a QMatrix burst charging sequence that uses different burst count values for
different Y lines, the Y lines may be incorrectly grounded for up to n-1 periods of the periph-
eral bus clock, where n is the ratio of the PB clock frequency to the GCLK_CAT frequency.
This results in premature loss of charge from the sense capacitors and thus increased vari-
ability of the acquired count values.
Fix/Workaround
Enable the 1kOhm drive resistors on all implemented QMatrix Y lines (CSA 1, 3, 5, 7, 9, 11,
13, and/or 15) by writing ones to the corresponding odd bits of the CSARES register.
When using the AST to trigger CAT autonomous touch acquisition in sleep modes where the
CAT bus clock is turned off, the CAT will start several acquisitions if the period of the AST
source clock is larger than one CAT acquisition. One AST clock period after the AST trigger,
the CAT clock will automatically stop and the CAT acquisition can be stopped prematurely,
ruining the result.
Fix/Workaround
Always ensure that the ATCFG1.max field is set so that the duration of the autonomous
touch acquisition is greater than one clock period of the AST source clock.
used
A CAT prescaler controlled by the ATCFG0.DIV field will be active even when the CAT mod-
ule is disabled or when the autonomous touch feature is not used, thereby causing
unnecessary power consumption.
Fix/Workaround
If the CAT module is not used, disable the CLK_CAT clock in the PM module. If the CAT
module is used but the autonomous touch feature is not used, the power consumption of the
CAT module may be reduced by writing 0xFFFF to the ATCFG0.DIV field.
The aWire MEMORY_SPEED_REQUEST command does not return a CV corresponding to
the formula in the aWire Debug Interface chapter.
Fix/Workaround
I s s u e a d u m m y r e a d t o a d d r e s s 0 x 1 0 0 0 0 0 0 0 0 b e f o r e i s s u i n g t h e
MEMORY_SPEED_REQUEST command and use this formula instead:
f
sab
=
---------------- -
CV 3
7f
aw
–
ATUC64/128/256L3/4U
81