ATmega88 Atmel Corporation, ATmega88 Datasheet - Page 83

• Manufacturer Part Number: ATmega88
• Manufacturer: Atmel Corporation

Specifications of ATmega88

• Flash (kbytes): 8 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 23
• Ext Interrupts: 24
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

2545T–AVR–05/11
PCINT9: Pin Change Interrupt source 9. The PC1 pin can serve as an external interrupt source.
• ADC0/PCINT8 – Port C, bit 0
PC0 can also be used as ADC input Channel 0. Note that ADC input channel 0 uses analog
power.
PCINT8: Pin Change Interrupt source 8. The PC0 pin can serve as an external interrupt source.
Table 14-7
shown in
Table 14-7.
Note:
Table 14-8.
Signal
name
PUOE
PUOV
DDOE
DDOV
PVOE
PVOV
DIEOE
DIEOV
DI
AIO
Signal
name
PUOE
PUOV
DDOE
DDOV
PVOE
PVOV
DIEOE
DIEOV
DI
AIO
1. When enabled, the 2-wire Serial Interface enables slew-rate controls on the output pins PC4
Figure 14-5 on page
PC6/RESET/PCINT14
RSTDISBL
1
RSTDISBL
0
0
0
RSTDISBL + PCINT14 •
PCIE1
RSTDISBL
PCINT14 INPUT
RESET INPUT
PC3/ADC3/
PCINT11
0
0
0
0
0
0
PCINT11 • PCIE1 +
ADC3D
PCINT11 • PCIE1
PCINT11 INPUT
ADC3 INPUT
and PC5. This is not shown in the figure. In addition, spike filters are connected between the
AIO outputs shown in the port figure and the digital logic of the TWI module.
and
Overriding signals for alternate functions in PC6..PC4
Overriding signals for alternate functions in PC3..PC0.
Table 14-8
relate the alternate functions of Port C to the overriding signals
76.
PC2/ADC2/
PCINT10
0
0
0
0
0
0
PCINT10 • PCIE1 +
ADC2D
PCINT10 • PCIE1
PCINT10 INPUT
ADC2 INPUT
PC5/SCL/ADC5/PCINT13
TWEN
PORTC5 • PUD
TWEN
SCL_OUT
TWEN
0
PCINT13 • PCIE1 + ADC5D
PCINT13 • PCIE1
PCINT13 INPUT
ADC5 INPUT / SCL INPUT
PC1/ADC1/
PCINT9
0
0
0
0
0
0
PCINT9 • PCIE1 +
ADC1D
PCINT9 • PCIE1
PCINT9 INPUT
ADC1 INPUT
ATmega48/88/168
PC4/SDA/ADC4/PCINT12
TWEN
PORTC4 • PUD
TWEN
SDA_OUT
TWEN
0
PCINT12 • PCIE1 + ADC4D
PCINT12 • PCIE1
PCINT12 INPUT
ADC4 INPUT / SDA INPUT
(1)
.
PC0/ADC0/
PCINT8
0
0
0
0
0
0
PCINT8 • PCIE1 +
ADC0D
PCINT8 • PCIE1
PCINT8 INPUT
ADC0 INPUT
83