AT32UC3C2256C Atmel Corporation, AT32UC3C2256C Datasheet - Page 133

• Manufacturer Part Number: AT32UC3C2256C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C2256C

• Flash (kbytes): 256 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 45
• Ext Interrupts: 64
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Can: 2
• Lin: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 13
• Input Capture Channels: 6
• Pwm Channels: 14
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

9.6.3.3
32002F–03/2010
Data Trace, Data Read (DTDR)
Table 9-44.
This message is output by the target processor when it detects a memory read that matches the
OCD system’s data trace attributes.
Table 9-45.
Data Trace, Data Write with Sync
message
Packet
Size
8 / 16 /
32
32
2
6
Data Trace, Data Read message
Packet
Size
8 / 16 /
32
32
2
6
3. Upon exit from a power-down state. This synchronization message is required to allow
4. The Event-In pin has been asserted and a debug control register field specifies that
5. An overrun condition had previously occurred in which one or more data trace occur-
6. The Data Trace Message counter has expired indicating that at most 256 without-sync
7. A data write is detected following the processor exiting from Debug Mode.
the unique portion of the data write address of following Data Trace, Data Write Mes-
sages to be correctly interpreted by the tool.
EVTI pin action is to generate data trace synchronization.
rences were discarded by the target processor’s debug logic. To inform the tool that an
overrun condition occurred,the target outputs an Error Message (TCODE = 8) with an
ECODE value of 00010 or 00111 immediately prior to the Data Trace, Data Write with
Sync Message.
versions of Data Trace Messages have been sent since the last with-sync version.
Packet
Name
DATA
F-ADDR
DSZ
TCODE
Packet
Name
DATA
U-ADDR
DSZ
TCODE
Data Trace, Data Write with Sync message
Data Trace, Data Read message
Packet
Type
Variable
Variable
Fixed
Fixed
Packet
Type
Variable
Variable
Fixed
Fixed
Direction: From target
Description
The data value written. The size will vary depending on the load /
store instruction being traced.
The full address of the memory location written. Most significant
bits that have a value of 0 are truncated.
Data size:
00 = 8 bits
01 = 16 bits
10 = 32 bits
Value=13
Direction: From target
Description
The data value read. The size will vary depending on the load /
store instruction being traced.
The unique portion of the data read address, which is relative to
the previous Data Trace Message (read or write).
Data size:
00 = 8 bits
01 = 16 bits
10 = 32 bits
Value=6
AVR32
133