TDA8595TH/N2C,118 NXP Semiconductors, TDA8595TH/N2C,118 Datasheet - Page 6

• Manufacturer Part Number: TDA8595TH/N2C,118
• Description: IC AMP AUDIO PWR 64W QUAD 36HSOP
• Manufacturer: NXP Semiconductors
• Type: Class ABr

Specifications of TDA8595TH/N2C,118

• Output Type: 4-Channel (Quad)
• Max Output Power X Channels @ Load: 64W x 4 @ 2 Ohm
• Voltage - Supply: 8 V ~ 18 V
• Features: Depop, I²C, Mute, Short-Circuit and Thermal Protection, Standby
• Mounting Type: Surface Mount
• Package / Case: 36-HSOP
• Product: Class-AB
• Operational Class: Class-AB
• Audio Amplifier Output Configuration: 4-Channel Stereo
• Output Power (typ): 25x4@4OhmW
• Audio Amplifier Function: Speaker
• Total Harmonic Distortion: 0.14@4Ohm@12W%
• Single Supply Voltage (typ): 14.4V
• Dual Supply Voltage (typ): Not RequiredV
• Power Supply Requirement: Single
• Power Dissipation: 80W
• Rail/rail I/o Type: No
• Single Supply Voltage (min): 8V
• Single Supply Voltage (max): 18V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 105C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 36
• Package Type: HSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 935284654118; TDA8595TH/N2C-T; TDA8595TH/N2C-T

NXP Semiconductors
7. Functional description
TDA8595_2
Product data sheet
Table 3.
[1]
The TDA8595 is a complementary quad BTL audio power amplifier made in BCDMOS
technology. It contains four independent amplifiers in BTL configuration (see
Through the I
programmable and the information to be shown on the two diagnostic pins can be
selected. The status of each amplifier (output offset, load or no load, short-circuit or
speaker incorrectly connected) can be read separately. The TDA8595 is protected against
overvoltage, short-circuit, over-temperature, open ground and open V
Three different I
ADSEL pin. If the ADSEL pin is short-circuit to ground, the TDA8595 operates in legacy
mode. In this mode, no I
two level (Standby mode and On mode) to a three level pin (Standby mode, On mode and
mute).
Symbol
n.c.
IN4
IN3
ACGND
OUT3+
n.c.
PGND3
OUT3
n.c.
V
OUT4+
SCL
OUT4
PGND4
SDA
n.c.
TAB
P1
To keep the output pins on the front side, special reverse bending is applied.
Pin description
2
Pin
TDA8595J
TDA8595SD
-
15
16
17
18
-
19
20
-
21
22
23
24
25
26
-
27
C-bus, the diagnostic functions of temperature level and clip level are fully
2
C-bus addresses are selected with an external resistor connected to the
Rev. 02 — 21 November 2007
2
C-bus is needed and the function of the STB pin will change from
[1]
…continued
TDA8595TH
10
11
12
13
14
15
16
17
18 and 19
20 and 21
25
22
23
24
26
27
36
I
2
C-bus controlled 4
Description
not connected
channel 4 input
channel 3 input
AC ground input
positive channel 3 output
not connected
power ground channel 3
negative channel 3 output
not connected
supply voltage 1
positive channel 4 output
I
negative channel 4 output
power ground channel 4
I
not connected
heatsink connection; must be connected to
ground
2
2
C-bus clock input
C-bus data input/output
45 W power amplifier
P
TDA8595
© NXP B.V. 2007. All rights reserved.
connections.
Figure
1).
6 of 50