MAX4409ETP+ Maxim Integrated Products, MAX4409ETP+ Datasheet - Page 14

• Manufacturer Part Number: MAX4409ETP+
• Description: IC AMP AUDIO .08W STER AB 20TQFN
• Manufacturer: Maxim Integrated Products
• Series: DirectDrive™r
• Type: Class ABr

Specifications of MAX4409ETP+

• Output Type: Headphones, 2-Channel (Stereo)
• Max Output Power X Channels @ Load: 80mW x 2 @ 16 Ohm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Features: Depop, Short-Circuit and Thermal Protection, Shutdown
• Mounting Type: Surface Mount
• Package / Case: 20-TQFN Exposed Pad
• Product: General Purpose Audio Amplifiers
• Output Power: 80 mW
• Common Mode Rejection Ratio (min): 96 dB
• Thd Plus Noise: 0.002 %
• Operating Supply Voltage: 1.8 V to 3.6 V
• Supply Current: 5 mA
• Maximum Power Dissipation: 2051 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Input Bias Current (max): 0 nA
• Input Offset Voltage: 0.5 mV
• Input Signal Type: Differential
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 1.8 V
• Amplifier Class: AB
• No. Of Channels: 2
• Supply Voltage Range: 1.8V To 3.6V
• Load Impedance: 16ohm
• Operating Temperature Range: -40°C To +85°C
• Amplifier Case Style: TQFN
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Application Circuit). Place capacitors C2 and C3 as
close to the device as possible. Route PGND and all
traces that carry switching transients away from SGND
and the traces and components in the audio signal
path.
Ensure that the COM traces have the same trace length
and width as the amplifier input and feedback traces.
Route COM traces away from noisy signal paths. The
thin QFN package features an exposed paddle that
80mW, DirectDrive, Stereo Headphone
Amplifier with Common-Mode Sense
Figure 6. Common-Mode Noise Rejection
14
______________________________________________________________________________________
EXAMPLE CONNECTION:
IMPROVEMENT FROM
ADDING MAX4409 WITH
SERIES RESISTANCE
V
AUDIO
V
AUDIO
RESISTOR IS
INSERTED
BETWEEN THE
JACK SLEEVE
AND
GND = 9.8Ω
MAX4409
9.8Ω
•
•
•
9.8Ω RESISTOR ADDS TO HP CROSSTALK, BUT DIFFERENTIAL
SENSING AT THE JACK SLEEVE CORRECTS FOR THIS (ONE CHANNEL
ONLY SHOWN).
CURRENT FLOW (IN SIGNAL CABLE SCREEN) DUE TO V
IS GREATLY REDUCED.
NOISE COMPONENT IN THE RECEIVER OUTPUT IS REDUCED BY 34dB
OVER THE PREVIOUS EXAMPLE WITH THE VALUES SHOWN.
•
•
•
0.10Ω RESISTANCE FROM CABLE SCREEN
0.10Ω RESISTANCE DUE TO GND CABLING AT RECEIVER
V
THE TWO GNDS
V
V
0.1Ω
0.1Ω
NOISE
NOISE
NOISE
REPRESENTS THE POTENTIAL DIFFERENCE BETWEEN
improves thermal efficiency of the package. However,
the MAX4409 does not require additional heatsinking.
Ensure that the exposed paddle is isolated from GND
or V
or V
DD
DD
0.1Ω
0.1Ω
. Do not connect the exposed paddle to GND
.
V
V
V
V
REF_IN
REF_IN
IN
IN
= V
= V
GND NOISE COMPONENT IN
OUTPUT = V
GND NOISE COMPONENT IN
OUTPUT = V
AUDIO
AUDIO
= V
= (V
NOISE
NOISE
+ (V
/2
NOISE
x 0.99)
NOISE
NOISE
x 0.98)
/2
/100
NOISE