SC28C94A1A,512 NXP Semiconductors, SC28C94A1A,512 Datasheet - Page 36
![IC UART QUAD W/FIFO 52-PLCC](/photos/6/82/68261/568-52-plcc_sot238-2_sml.jpg)
SC28C94A1A,512
Manufacturer Part Number
SC28C94A1A,512
Description
IC UART QUAD W/FIFO 52-PLCC
Manufacturer
NXP Semiconductors
Type
Quad UARTr
Datasheet
1.SC28C94A1A518.pdf
(39 pages)
Specifications of SC28C94A1A,512
Number Of Channels
4, QUART
Package / Case
52-PLCC
Features
False-start Bit Detection
Fifo's
8 Byte
Voltage - Supply
5V
With Auto Flow Control
Yes
With False Start Bit Detection
Yes
With Modem Control
Yes
With Cmos
Yes
Mounting Type
Surface Mount
Data Rate
1 Mbps
Supply Voltage (max)
5.5 V
Supply Voltage (min)
4.5 V
Supply Current
35 mA
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Operating Supply Voltage
5 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
568-3993-5
935262534512
SC28C94A1A
SC28C94A1A
935262534512
SC28C94A1A
SC28C94A1A
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SC28C94A1A,512
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Philips Semiconductors
addressed register. The generation of DACKN begins with the start
of a bus cycle (Read, Write or Interrupt Acknowledge) and then
requires two edges of the X1 clock plus typically 70ns for its
assertion.
In this mode the writing of data to the QUART registers occurs on
the falling edge of DACKN or the rising edge of the combination of
CEN and WRN which ever occurs first. This requires that the data
to be written to the QUART registers be valid with respect to the
leading edge of the combination of CEN and WRN. (In the
synchronous mode it is the trailing edge)
IACKN updates the CIR (Current Interrupt Register) and places the
Interrupt Vector or Modified Interrupt Vector on the bus if the
Interrupt Vector is used.
The Synchronous Interface
In this mode the DACKN and IACKN are usually not used. Here
data is written to the QUART on the trailing edge of the
combination of CEN and WRN. The placing of data on the bus
during a read cycle begins with the leading edge of the combination
of CEN and RDN.
The read cycle will terminate with the rise of CEN or RDN which
ever one occurs first. In this mode bus cycles are usually setup to be
the minimum time required by the QUART and hence will be faster
than bus cycles that are defined by the DACKN signal. DACKN
should be turned off in this mode.
2006 Aug 09
Quad universal asynchronous receiver/transmitter (QUART)
36
The synchronous mode usually will not use the IACKN and DACKN.
When IACKN is not used or is not available the command at 2Ah
should be used to update the CIR (Current Interrupt Register). This
register is normally updated by IACKN in response to the IRQN.
Note that the CIR is not updated by IRQN since there could be a
long time between the assertion of IRQN and the start of the
interrupt service routine. During this time it is quite possible that
another interrupt with a higher priority occurs. It is the CIR that
contains the information that describes the interrupt source and its
priority. It is therefor recommended that the first operation upon
entering the interrupt service routine is the updating of the CIR.
(Recall that the contents of the GLOBAL registers reflect the content
of the CIR)
Summary
In the asynchronous mode all of the interface pins are usually used.
However there is no conflict in the quart if both modes are used in
the same application. (i.e. More than one device may control the
QUART) The principles to keep in mind are:
1. When IACKN is not used the CIR should be updated via
2. If DACKN is not used it should be disabled.
3. When in the asynchronous mode be sure DACKN is enabled.
4. With 68xxx type controllers the RDN signal must be generated.
command.
SC28C94
Product data sheet