LPC1787FBD208,551 NXP Semiconductors, LPC1787FBD208,551 Datasheet - Page 54
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
LPC1787FBD208,551
Manufacturer Part Number
LPC1787FBD208,551
Description
IC MCU 32BIT 512KB FLASH 208LQFP
Manufacturer
NXP Semiconductors
Series
LPC17xxr
Datasheet
1.LPC1774FBD208551.pdf
(117 pages)
Specifications of LPC1787FBD208,551
Core Processor
ARM® Cortex-M3™
Core Size
32-Bit
Speed
120MHz
Connectivity
CAN, EBI/EMI, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
Peripherals
Brown-out Detect/Reset, DMA, I²S, LCD, Motor Control PWM, POR, PWM, WDT
Number Of I /o
165
Program Memory Size
512KB (512K x 8)
Program Memory Type
FLASH
Eeprom Size
4K x 8
Ram Size
96K x 8
Voltage - Supply (vcc/vdd)
2.4 V ~ 3.6 V
Data Converters
A/D 8x12b, D/A 1x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
208-LQFP
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
568-7575
LPC1787FBD208,551
LPC1787FBD208,551
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LPC1787FBD208,551
Manufacturer:
NXP Semiconductors
Quantity:
10 000
NXP Semiconductors
LPC178X_7X
Objective data sheet
7.21.1 Features
7.22.1 Features
7.22 I
during a given data transfer. The SSP supports full duplex transfers, with frames of 4 bits
to 16 bits of data flowing from the master to the slave and from the slave to the master. In
practice, often only one of these data flows carries meaningful data.
The LPC178x/7x contain three I
The I
(SCL) and a Serial Data Line (SDA). Each device is recognized by a unique address and
can operate as either a receiver-only device (e.g., an LCD driver) or a transmitter with the
capability to both receive and send information (such as memory). Transmitters and/or
receivers can operate in either master or slave mode, depending on whether the chip has
to initiate a data transfer or is only addressed. The I
controlled by more than one bus master connected to it.
2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
C-bus serial I/O controllers
Maximum SSP speed of 60 Mbit/s (master) or 10 Mbit/s (slave)
Compatible with Motorola SPI, 4-wire Texas Instruments SSI, and National
Semiconductor Microwire buses
Synchronous serial communication
Master or slave operation
8-frame FIFOs for both transmit and receive
4-bit to 16-bit frame
DMA transfers supported by GPDMA
All I
(Fast I
up to 400 kbit/s.
The I
using pins P5[2] and P5[3].
Easy to configure as master, slave, or master/slave.
Programmable clocks allow versatile rate control.
Bidirectional data transfer between masters and slaves.
Multi-master bus (no central master).
Arbitration between simultaneously transmitting masters without corruption of serial
data on the bus.
Serial clock synchronization allows devices with different bit rates to communicate via
one serial bus.
Serial clock synchronization can be used as a handshake mechanism to suspend and
resume serial transfer.
The I
Both I
mode.
2
C-bus is bidirectional for inter-IC control using only two wires: a Serial Clock Line
2
C-bus controllers can use standard GPIO pins with bit rates of up to 400 kbit/s
2
2
2
C-bus interface supports Fast-mode Plus with bit rates up to 1 Mbit/s for I2C0
C-bus can be used for test and diagnostic purposes.
2
C-bus controllers support multiple address recognition and a bus monitor
C-bus). The I
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 27 May 2011
2
C0-bus interface uses special open-drain pins with bit rates of
2
C-bus controllers.
32-bit ARM Cortex-M3 microcontroller
2
C is a multi-master bus and can be
LPC178x/7x
© NXP B.V. 2011. All rights reserved.
54 of 117