DS90C387VJDX National Semiconductor, DS90C387VJDX Datasheet - Page 13

• Manufacturer Part Number: DS90C387VJDX
• Description: LVDS Flat Panel Display 0.45V 100-Pin TQFP T/R
• Manufacturer: National Semiconductor

Specifications of DS90C387VJDX

• Package: 100TQFP
• Number Of Elements Per Chip: 8
• Transmission Data Rate: 5380 Mbps
• Differential Input Low Threshold Voltage: -0.1 V
• Differential Input High Threshold Voltage: 0.1 V
• Typical Operating Supply Voltage: 3.3 V

DS90C387 Pin Descriptions — FPD Link Transmitter
Note 12: Inputs default to “low” when left open due to internal pull-down resistor.
Note 13: DC Balancing is functionally tested on Automatic Test Equipment (ATE) at 85 MHz only. A sample of characterization units have been bench tested at 112
MHz to verify full speed performance.
Note 14: The PLL range shift point is in the 55 - 68 MHz range, typically the shift will occur during the lock time.
Rn, Gn, Bn,
DE, HSYNC,
VSYNC
AnP
AnM
CLKIN
R_FB
R_FDE
CLK1P
CLK1M
PD
PLLSEL
BAL
PRE
DUAL
V
GND
PLLV
PLLGND
LVDSV
LVDSGND
CLK2P/NC
CLK2M/NC
CC
Pin Name
CC
CC
I/O
O
O
O
O
O
O
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
No.
51
8
8
1
1
1
1
1
1
1
1
1
1
4
5
2
3
3
4
1
1
TTL level input. This includes: 16 Red, 16 Green, 16 Blue, and 3 control
lines HSYNC, VSYNC, DE (Data Enable).(Note 12)
Positive LVDS differential data output.
Negative LVDS differential data output.
TTL level clock input.
Programmable data strobe select. Rising data strobe edge selected when
input is high. (Note 12)
Programmable control (DE) strobe select. Tied high for data active when DE
is high. (Note 12)
Positive LVDS differential clock output.
Negative LVDS differential clock output.
TTL level input. Assertion (low input) tri-states the outputs, ensuring low
current at power down. (Note 12)
PLL range select. This pin must be tied to V
Ground is reserved for future use. Typical shift point is between 55 and 68
MHz. (Notes 12, 14)
Mode select for DC Balanced (new) or non-DC Balanced (backward
compatible) interface. DC Balance is active when input is high. NC or tied to
Ground, the DC Balance function is disabled. (Notes 12, 13, 15)
Pre-emphasis level select. Pre-emphasis is active when input is tied to V
through external pull-up resistor. Resistor value determines pre-emphasis
level (see table in application section). For normal LVDS drive level (No
pre-emphasis) leave this pin open (do not tie to ground).(Note 12)
Three-mode select for dual pixel, single pixel, or single pixel input to dual
pixel output operation. Single pixel mode when input is low (only LVDS
channels A0 thru A3 and CLK1 are active) for power savings. Dual mode is
active when input is high. Single in - dual out when input is at 1/2 Vcc. (Note
12)Figure 16
Power supply pins for TTL inputs and digital circuitry.
Ground pins for TTL inputs and digital circuitry.
Power supply pin for PLL circuitry.
Ground pins for PLL circuitry.
Power supply pin for LVDS outputs.
Ground pins for LVDS outputs.
Additional positive LVDS differential clock output. Identical to CLK1P. No
connect if not used.
Additional negative LVDS differential clock output. Identical to CLK1M. No
connect if not used.
13
Description
CC
for auto-range. NC or tied to
www.national.com
CC