PC82573E Intel, PC82573E Datasheet - Page 16

no-image

PC82573E

Manufacturer Part Number
PC82573E
Description
Ethernet CTLR Single Chip 10Mbps/100Mbps/1000Mbps 1.2V/2.5V/3.3V 196-Pin TFBGA
Manufacturer
Intel
Datasheet

Specifications of PC82573E

Package
196TFBGA
Standard Supported
IEEE 1149.1|IEEE 802.3|IEEE 802.3ab|IEEE 802.3q1|IEEE 802.3x
Communication Mode
Full Duplex|Half Duplex
Data Rate
10|100|1000 Mbps
Host Interface
PCI
Operating Supply Voltage
1.2|2.5|3.3 V
Dma Support
Yes
Maximum Power Dissipation
1.35 W

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PC82573E
Manufacturer:
NS
Quantity:
1 831
Part Number:
PC82573E
Manufacturer:
INTEL/英特尔
Quantity:
20 000
2.8
2.8.1
2.8.2
2.9
16
Power Signals
Power Support Signals
Digital and Analog Power Supply Signals
1. This signal is used in all three devices and has the same functionality but is denoted as IREG25_IN for the
Grounds and No Connects
CTRL_25
CTRL_12
EN25REG
VCC33
VCC25
VCC12
IREG25_IN
(82573E/V)
VCC3.3_REG25
(82573L only)
VCC25_OUT
VSS
NC
82573E/V and VCC3.3_REG25 for the 82573L.
Signal
Signal
Signal
1
P
P
I/PU
P
P
P
P
P
P
Type
Type
Type
2.5V Control
This is the voltage control signal for external 2.5V. It is only active when the
EN25REG signal is low (disabled). When external 2.5V and 1.2V supplies are used,
CTRL_25 can be left floating or can be connected to ground through a 3.3 KΩ
resistor.
1.2V Control
This is the voltage control signal for external 1.2V. When external 2.5V and 1.2V
supplies are used, CTRL_12 can be left floating or can be connected to ground
through a 3.3 KΩ resistor.
Enable 2.5V Regulator
When this signal is high, the internal 2.5V regulator is enabled. When it is low, the
internal 2.5V regulator is disables and the CTRL_25 signal is active. This signal
should be pulled up to the 3.3V power rail.
3.3V Power Supply
This signal is used for I/O circuits.
2.5V Analog Power Supply
These signals are used for PHY analog, PHY I/O, PCIe* analog and phase lock loop
circuits. All 2.5V pins should be connected to a single power supply.
1.2V Digital Power Supply
These signals are used for core digital, PHY digital, PCIe* digital and clock circuits.
All 1.2V pins should be connected to a single power supply.
IREG25_IN
3.3V power supply for internal 2.5V regulator. When external 2.5V and 1.2V
supplies are used, IREG25_IN should be connected to 3.3V.
VCC25_OUT
2.5V output supply from internal power supply. When external 2.5V and 1.2V
supplies are used, VCC25_OUT can be left floating.
Ground
These signals connect to ground.
VSS is also referred to as GND.
No Connect
These pins are reserved by Intel and might have factory test functions. For normal
operation, do not connect any circuitry to these pins. Do not connect pull-up or
pull-down resistors.
Name and Function
Name and Function
Name and Function
82573—Datasheet

Related parts for PC82573E