TDA5231XT Infineon Technologies, TDA5231XT Datasheet - Page 110
TDA5231XT
Manufacturer Part Number
TDA5231XT
Description
Manufacturer
Infineon Technologies
Datasheet
1.TDA5231XT.pdf
(186 pages)
Specifications of TDA5231XT
Operating Temperature (min)
-40C
Operating Temperature (max)
105C
Operating Temperature Classification
Industrial
Product Depth (mm)
4.4mm
Product Length (mm)
9.7mm
Lead Free Status / Rohs Status
Compliant
- Current page: 110 of 186
- Download datasheet (4Mb)
TDA523x
Functional Description
clock recovery reset
start point
valid data
valid data
TSI A
TSI GAP
TSI B
RUNIN
GAPSync
< 1bit
< 1bit
PLL sync
internal PLL sync
Figure 54
Clock Recovery GAP Re-synchronization Mode 1
When the time TSI GAP in the start sequence of the transmitted telegram has elapsed,
the receiver needs a certain time (GAPSync = 5...6 chips) to readjust the PLL settings.
Behavior of the system at the starting position of the TSI B:
The starting position (TSI B start) for the TSI B comparison is independent from the
RUNIN settings (CDR2 register) and the Re-synchronization mode (TSIMODE register):
[
]
[
]
TSIBstart chips
=
TSIGAP chips
+
6…8
The incoming chips at TSI B start and the following incoming chips are compared with
the contents of the register TSI B. Please notice that the receiver’s PLL runs at the data
rate determined before the gap. Therefore, the receiver calculates the gap based on this
data rate.
Behavior of the system at the ending position of TSI B:
The system checks for the TSI B to match within a limited time. If there is no match within
this time, then the receiver starts again to search for the TSI A pattern at the following
incoming chips:
[
]
[
]
[
]
TSIBstop chips
=
TSIGAP chips
+
TSILENB chips
+
11
For a successful TSI B pattern match, the defined TSI B pattern must be between “Start
of TSIB” and “Stop of TSI B”. In the example below, the earliest possible start position
th
nd
would be the 18
chip and the latest possible start position would be the 22
chip.
Please note that after a gap the internal TSI comparison register is cleared (all chips set
to ’0’). In this case, a TSI B criteria of “0000” would always match at the beginning. To
avoid such an unwanted matching, set the highest TSI B match chip to ’1’.
Data Sheet
106
Version 4.0, 2007-06-01
Related parts for TDA5231XT
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
16-bit microcontroller with 2x2 KByte RAM
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
NPN silicon RF transistor
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
NPN silicon RF transistor
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
NPN silicon RF transistor
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
NPN silicon RF transistor
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Si-MMIC-amplifier in SIEGET 25-technologie
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
IGBT Power Module
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
IC for switching-mode power supplies
Manufacturer:
Infineon Technologies AG
Datasheet: