LH28F800BVHE-BTL90 Sharp Electronics, LH28F800BVHE-BTL90 Datasheet
![no-image](/images/manufacturer_photos/0/6/602/sharp_electronics_sml.jpg)
LH28F800BVHE-BTL90
Specifications of LH28F800BVHE-BTL90
Available stocks
Related parts for LH28F800BVHE-BTL90
LH28F800BVHE-BTL90 Summary of contents
Page 1
... P S RODUCT PECIFICATIONS LH28F800BVHE-BTL90 8M (1MB × 512KB × 16) ® Flash Memory (Model No.: LHF80V13) Spec No.: EL109049B Issue Date: September 28, 1999 Integrated Circuits Group ...
Page 2
...
Page 3
Any reproduction, full or in part, of this material is prohibited without the express written permission of the company. ●When using the products covered herein, please ...
Page 4
INTRODUCTION.............................................................. 3 1.1 Features ........................................................................ 3 1.2 Product Overview......................................................... 3 2 PRINCIPLES OF OPERATION........................................ 7 2.1 Data Protection............................................................. 8 3 BUS OPERATION ............................................................ 8 3.1 Read.............................................................................. 8 3.2 Output Disable.............................................................. 8 3.3 Standby......................................................................... 8 3.4 Deep Power-Down ....................................................... ...
Page 5
... Its enhanced suspend capabilities provide for an ideal solution for code + data storage applications. For secure code storage applications, such as networking, where code is either directly executed out of flash or downloaded to DRAM, the LH28F800BVHE-BTL90 offers two levels of protection: absolute protection with V at GND, selective hardware boot block locking ...
Page 6
... Smart3 technology, allow V and V connection to 2.7V-3.6V. PP 1.2 Product Overview The LH28F800BVHE-BTL90 is a high-performance 8M- bit Smart3 Flash memory organized as 1M-byte of 8 bits or 512K-word of 16 bits. The 1M-byte/512K-word of data is arranged in two 8K-byte/4K-word boot blocks, six 8K- byte/4K-word parameter blocks and fifteen 64K-byte/32K- word main blocks which are individually erasable in- system ...
Page 7
The boot blocks can be locked for the WP# pin. Block erase or word/byte write for boot block must not be carried out by WP# to Low and RP The status register indicates when the ...
Page 8
Input Decoder Buffer Address Latch Decoder Address Counter ...
Page 9
... V not be attempted. DEVICE POWER SUPPLY: Do not float any power pins. With V V SUPPLY the flash memory are inhibited. Device operations at invalid V CC produce spurious results and should not be attempted. GND SUPPLY GROUND: Do not float any ground pins. ...
Page 10
... PRINCIPLES OF OPERATION The LH28F800BVHE-BTL90 Smart3 Flash memory includes an on-chip WSM to manage block erase and word/byte write functions. It allows for: 100% TTL-level control inputs, fixed power supplies during block erasure and word/byte write, and minimal processor overhead with RAM-like interface timings. ...
Page 11
... Refer to Table 6 for write protection alternatives. 3 BUS OPERATION The local CPU reads and writes flash memory in-system. All bus cycles to or from the flash memory conform to standard microprocessor bus cycles. 3.1 Read Information can be read from any block, identifier codes ...
Page 12
Read Identifier Codes Operation The read identifier codes operation manufacturer code and device code (see Figure 4). Using the manufacturer and device codes, the system CPU can automatically match the device with its proper algorithms ...
Page 13
Mode Notes Read 8 Output Disable Standby 10 Deep Power-Down 4,10 Read Identifier Codes 8 Write 6,7,8 Mode Notes V Read 8 V Output Disable V Standby 10 Deep Power-Down 4,10 V Read Identifier Codes 8,9 V Write 6,7,8 ...
Page 14
Bus Cycles Command Req’d. Read Array/Reset 1 ≥2 Read Identifier Codes Read Status Register 2 Clear Status Register 1 Block Erase 2 Word/Byte Write 2 Block Erase and Word/Byte 1 Write Suspend Block Erase and Word/Byte 1 Write Resume ...
Page 15
Read Array Command Upon initial device power-up and after exit from deep power-down mode, the device defaults to read array mode. This operation is also initiated by writing the Read Array command. The device remains enabled for reads ...
Page 16
... HH suspended are Read Status Register and Block Erase Resume. After a Block Erase Resume command is written to the flash memory, the WSM will continue the block erase process. Status register bits SR.6 and SR.7 will automatically clear and RY/BY# will return to V the Erase Resume command is written, the device automatically outputs status register data when read (see Figure 7) ...
Page 17
... V The V PP complete write protection of all blocks in the flash device. 4.10.2 WP#=V The lockable blocks are locked when WP#=V program or erase operation to a locked block will result in an error, which will be reflected in the status register. For top configuration, the top two boot blocks are lockable ...
Page 18
WSMS ESS SR.7 = WRITE STATE MACHINE STATUS (WSMS Ready 0 = Busy SR.6 = ERASE SUSPEND STATUS (ESS Block Erase Suspended 0 = Block Erase in Progress/Completed SR.5 = ERASE ...
Page 19
Start Write 20H, Block Address Write D0H, Block Address Read Status Register No 0 Suspend SR.7= Block Erase Yes 1 Full Status Check if Desired Block Erase Complete FULL STATUS CHECK PROCEDURE Read Status Register Data(See Above) 1 SR.3= ...
Page 20
Start Write 40H or 10H, Address Write Word/Byte Data and Address Read Status Register No 0 Suspend SR.7= Word/Byte Write Yes 1 Full Status Check if Desired Word/Byte Write Complete FULL STATUS CHECK PROCEDURE Read Status Register Data(See Above) ...
Page 21
Start Write B0H Read Status Register 0 SR. SR.6= Block Erase Completed 1 Read or Read Word/Byte Write Word/Byte Write? Read Array Data Word/Byte Write Loop No Done? Yes Write D0H Block Erase Resumed Read Array Data ...
Page 22
Start Write B0H Read Status Register 0 SR. Word/Byte Write SR.2= Completed 1 Write FFH Read Array Data Done No Reading Yes Write D0H Write FFH Word/Byte Write Read Array Data Resumed Figure 8. Word/Byte Write Suspend/Resume ...
Page 23
... PC board trace inductance. 5.4 V Trace on Printed Circuit Boards PP Updating flash memories that reside in the target system requires that the printed circuit board designer pay attention to the V Power supply trace. The V PP supplies the memory cell current for word/byte writing and block erasing ...
Page 24
... When designing portable systems, designers must consider clear IL battery power consumption not only during device operation, but also for data retention during system idle time. Flash memory’s nonvolatility increases usable battery life because data is retained when system power is removed. . LKO ...
Page 25
ELECTRICAL SPECIFICATIONS 6.1 Absolute Maximum Ratings* Operating Temperature During Read, Block Erase and Word/Byte Write..............................-40°C to +85°C Temperature under Bias ...................... -40°C to +85°C Storage Temperature ................................ -65°C to +125°C Voltage On Any Pin (except ...
Page 26
AC INPUT/OUTPUT TEST CONDITIONS 2.7 INPUT 0.0 AC test inputs are driven at 2.7V for a Logic "1" and 0.0V for a Logic "0." Input timing begins, and output timing ends, at 1.35V. Input rise and fall times ...
Page 27
DC CHARACTERISTICS Sym. Parameter I Input Load Current LI I Output Leakage Current Standby Current CCS Deep Power-Down Current CCD Read Current CCR Word/Byte Write Current ...
Page 28
Sym. Parameter V Input Low Voltage IL V Input High Voltage IH V Output Low Voltage OL V Output High Voltage OH1 (TTL) V Output High Voltage OH2 (CMOS Lockout Voltage during Normal PPLK PP Operations V ...
Page 29
AC CHARACTERISTICS - READ-ONLY OPERATIONS Sym. Parameter t Read Cycle Time AVAV t Address to Output Delay AVQV t CE# to Output Delay ELQV t RP# High to Output Delay PHQV t OE# to Output Delay GLQV t ...
Page 30
Standby Address Selection V IH ADDRESSES( CE#( OE#( WE#( HIGH Z DATA(D/Q) (DQ - PHQV ...
Page 31
Standby Address Selection V IH ADDRESSES( CE#( OE#( BYTE#( HIGH Z DATA(D/Q) (DQ - HIGH Z ...
Page 32
AC CHARACTERISTICS - WRITE OPERATIONS Sym. Parameter t Write Cycle Time AVAV t RP# High Recovery to WE# Going Low PHWL t CE# Setup to WE# Going Low ELWL t WE# Pulse Width WLWH t RP# V Setup ...
Page 33
V IH ADDRESSES( CE#( OE#( WE#( DATA(D/ BYTE#( High Z RY/BY#( WP#(S) V ...
Page 34
ALTERNATIVE CE#-CONTROLLED WRITES Sym. Parameter t Write Cycle Time AVAV t RP# High Recovery to CE# Going Low PHEL t WE# Setup to CE# Going Low WLEL t CE# Pulse Width ELEH t RP# V Setup to CE# ...
Page 35
V IH ADDRESSES( CE#( OE#( WE#( DATA(D/ BYTE#( High Z RY/BY#( WP#(S) V ...
Page 36
RESET OPERATIONS High Z RY/BY#( RP#( High Z RY/BY#( RP#( 2. RP#( Sym. RP# Pulse Low Time t ...
Page 37
BLOCK ERASE AND WORD/BYTE WRITE PERFORMANCE Sym. Parameter t Word/Byte Write Time 32K word Block WHQV1 t 4K word Block EHQV1 Block Write Time 32K word Block 4K word Block t Block Erase Time 32K word Block WHQV2 ...
Page 38
...
Page 39
...
Page 40
...
Page 41
...
Page 42
...
Page 43
...
Page 44
...
Page 45
A-1 RECOMMENDED OPERATING CONDITIONS A-1.1 At Device Power-Up AC timing illustrated in Figure A-1 is recommended for the supply voltages and the control signals at device power-up. If the timing in the figure is ignored, the device may not ...
Page 46
A-1.1.1 Rise and Fall Time Symbol t V Rise Time Input Signal Rise Time R t Input Signal Fall Time F NOTES: 1. Sampled, not 100% tested. 2. This specification is applied for not only the ...
Page 47
A-1.2 Glitch Noises Do not input the glitch noises which are below V as shown in Figure A-2 (b). The acceptable glitch noises are illustrated in Figure A-2 (a). Input Signal V (Min (Max.) IL Input Signal ...
Page 48
... A-2 RELATED DOCUMENT INFORMATION Document No. AP-001-SD-E AP-006-PT-E AP-007-SW-E NOTE: 1. International customers should contact their local SHARP or distribution sales office. (1) Document Name Flash Memory Family Software Drivers Data Protection Method of SHARP Flash Memory RP#, V Electric Potential Switching Circuit PP iv Rev. 1.10 ...
Page 49
... Head Office: No. 360, Bashen Road, Xin Development Bldg. 22 Waigaoqiao Free Trade Zone Shanghai 200131 P.R. China Email: smc@china.global.sharp.co.jp EUROPE SHARP Microelectronics Europe Division of Sharp Electronics (Europe) GmbH Sonninstrasse 3 20097 Hamburg, Germany Phone: (49) 40-2376-2286 Fax: (49) 40-2376-2232 www.sharpsme.com SINGAPORE SHARP Electronics (Singapore) PTE., Ltd. ...