SAK-C167CS-L33M Infineon Technologies, SAK-C167CS-L33M Datasheet - Page 55

• Manufacturer Part Number: SAK-C167CS-L33M
• Manufacturer: Infineon Technologies

Specifications of SAK-C167CS-L33M

• Cpu Family: C166
• Device Core Size: 16b
• Frequency (max): 33MHz
• Interface Type: CAN/SPI/USART
• Program Memory Type: ROMLess
• Program Memory Size: Not Required
• Total Internal Ram Size: 11KB
• # I/os (max): 111
• Number Of Timers - General Purpose: 5
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4.5V
• On-chip Adc: 24-chx10-bit
• Instruction Set Architecture: CISC/RISC
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 144
• Package Type: MQFP
• Lead Free Status / Rohs Status: Supplier Unconfirmed

DC Characteristics (cont’d)
(Operating Conditions apply)
Parameter
Input leakage current (all other)
RSTIN inactive current
RSTIN active current
READY/RD/WR inact. current
READY/RD/WR active current
ALE inactive current
ALE active current
Port 6 inactive current
Port 6 active current
PORT0 configuration current
XTAL1 input current
Pin capacitance
(digital inputs/outputs)
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
Data Sheet
Keeping signal levels within the levels specified in this table, ensures operation without overload conditions.
For signal levels outside these specifications also refer to the specification of the overload current
For pin RSTIN this specification is only valid in bidirectional reset mode.
The maximum deliverable output current of a port driver depends on the selected output driver mode, see
Table
As a rule, with decreasing output current the output levels approach the respective supply level (
V
This specification is not valid for outputs which are switched to open drain mode. In this case the respective
output will float and the voltage results from the external circuitry.
These parameters describe the RSTIN pullup, which equals a resistance of ca. 50 to 250 kΩ.
The maximum current may be drawn while the respective signal line remains inactive.
The minimum current must be drawn in order to drive the respective signal line active.
This specification is valid during Reset and during Hold-mode or Adapt-mode. During Hold-mode Port 6 pins
are only affected, if they are used (configured) for CS output and the open drain function is not enabled. The
READY-pullup is always active, except for Powerdown mode.
This specification is valid during Reset and during Adapt-mode.
Not 100% tested, guaranteed by design and characterization.
OH
→ V
10,
DD
Current Limits for Port Output
). However, only the levels for nominal output currents are guaranteed.
11)
9)
9)
9)
6)
9)
6)
1)
10)
9)
9)
Symbol
I
I
I
I
I
I
I
I
I
I
I
I
C
OZ2
RSTH
RSTL
RWH
RWL
ALEL
ALEH
P6H
P6L
P0H
P0L
IL
IO
Drivers. The limit for pin groups must be respected.
8)
8)
7)
7)
8)
7)
7)
8)
8)
7)
CC –
CC –
CC –
51
min.
–
-100
–
-500
–
500
–
-500
–
-100
Limit Values
max.
± 500
-10
–
-40
–
40
–
-40
–
-10
–
± 20
10
Unit Test Condition
nA
µ A
µ A
µ A
µ A
µ A
µ A
µ A
µ A
µ A
µ A
µ A
pF
0.45 V <
<
V
V
V
V
V
V
V
V
V
V
0 V <
f
T
= 1 MHz
A
IN
IN
OUT
OUT
OUT
OUT
OUT
OUT
IN
IN
V
= 25 ° C
DD
C167CS-4R
=
=
=
=
V2.2, 2001-08
C167CS-L
V
V
= 2.4 V
=
=
= 2.4 V
= 2.4 V
=
V
V
V
IH1
IL
IHmin
ILmax
IN
V
V
V
V
I
V
OL
OLmax
OLmax
OL1max
OV
<
IN
→ V
.
V
DD
SS
,