PVX003A0X3-SRZ Lineage Power, PVX003A0X3-SRZ Datasheet - Page 13

• Manufacturer Part Number: PVX003A0X3-SRZ
• Description: DC/DC Converters & Regulators 3-14.4Vin .6-5.5V 3A Neg Logic SMT Analog
• Manufacturer: Lineage Power
• Series: PVXr

Specifications of PVX003A0X3-SRZ

• Product: Non-Isolated / POL
• Input Voltage Range: 3 VDC to 14.4 VDC
• Number Of Outputs: 1
• Output Voltage (channel 1): 0.6 VDC to 5.5 VDC
• Output Current (channel 1): 3 A
• Package / Case Size: 12.2 mm x 12.2 mm x 6.25 mm
• Output Type: Non-Isolated
• Output Voltage: 0.6 VDC to 5.5 VDC
• Lead Free Status / Rohs Status: Details

Preliminary Data Sheet
January 19, 2012
Feature Descriptions
Remote On/Off
The 3A Analog Pico DLynx
an On/Off pin for remote On/Off operation. Two
On/Off logic options are available. In the Positive
Logic On/Off option, (device code suffix “4” – see
Ordering Information), the module turns ON during a
logic High on the On/Off pin and turns OFF during a
logic Low. With the Negative Logic On/Off option, (no
device code suffix, see Ordering Information), the
module turns OFF during logic High and ON during
logic Low. The On/Off signal should be always
referenced to ground. For either On/Off logic option,
leaving the On/Off pin disconnected will turn the
module ON when input voltage is present.
For positive logic modules, the circuit configuration for
using the On/Off pin is shown in Figure 39. When the
external transistor Q1 is in the OFF state, the internal
PWM Enable signal is pulled high through an internal
resistor and the external pullup resistor and the
module is ON. When transistor Q1 is turned ON, the
On/Off pin is pulled low and the module is OFF. A
suggested value for R
TBA
Figure 39. Circuit configuration for using positive
On/Off logic.
For negative logic On/Off modules, the circuit
configuration is shown in Fig. 40. The On/Off pin
should be pulled high with an external pull-up resistor
(suggested value for the 3V to 14.4V input range is
20Kohms). When transistor Q1 is in the OFF state, the
On/Off pin is pulled high, internal transistor Q4 is
turned ON and the module is OFF. To turn the module
ON, Q1 is turned ON pulling the On/Off pin low, turning
transistor Q4 OFF resulting in the PWM Enable pin
going high and the module turning ON.
Figure 40. Circuit configuration for using negative
On/Off logic.
LINEAGE
ON/OFF
VIN+
Rpullup
Q1
GND
I
ON/OFF
POWER
V
ON/OFF
_
+
MODULE
pullup
is TBD
TM
22K
22K
power modules feature
3A Analog Pico DLynx
PWM Enable
3 – 14.4Vdc input; 0.6Vdc to 5.5Vdc output; 3A output current
Q4
CSS
Monotonic Start-up and Shutdown
The module has monotonic start-up and shutdown
behavior for any combination of rated input voltage,
output current and operating temperature range.
Startup into Pre-biased Output
The modules can start into a prebiased output as long
as the prebias voltage is 0.5V less than the set output
voltage.
Output Voltage Programming
The output voltage of the module is programmable to
any voltage from 0.6dc to 5.5Vdc by connecting a
resistor between the Trim and GND pins of the
module. Certain restrictions apply on the output
voltage set point depending on the input voltage.
These are shown in the Output Voltage vs. Input
Voltage Set Point Area plot in Fig. 41. The Upper Limit
curve shows that for output voltages lower than 1V, the
input voltage must be lower than the maximum of 12V.
The Lower Limit curve shows that for output voltages
higher than 0.6V, the input voltage needs to be larger
than the minimum of 3V.
Point Area plot showing limits where the output
voltage can be set for different input voltages.
Figure 42. Circuit configuration for programming
output voltage using an external resistor.
Figure 41. Output Voltage vs. Input Voltage Set
TM
16
14
12
10
8
6
4
2
0
: Non-isolated DC-DC Power Modules
0.5
V
ON/OFF
IN
(+)
1
1.5
2
TRIM
V
GND
VS+
O
Output Voltage
(+)
2.5
Upper Limit
3
3.5
Lower Limit
4
R
trim
4.5
5
5.5
LOAD
13
6