HCF4051BEY STMicroelectronics, HCF4051BEY Datasheet - Page 6

• Manufacturer Part Number: HCF4051BEY
• Description: IC MUX/DEMUX 8X1 16DIP
• Manufacturer: STMicroelectronics
• Series: 4000Br
• Type: Analog Multiplexerr

Specifications of HCF4051BEY

• Function: Multiplexer/Demultiplexer
• Circuit: 1 x 8:1
• On-state Resistance: 280 Ohm
• Voltage Supply Source: Dual Supply
• Voltage - Supply, Single/dual (±): ±3 V ~ 20 V
• Current - Supply: .08µA
• Operating Temperature: -55°C ~ 125°C
• Mounting Type: Through Hole
• Package / Case: 16-DIP (0.300", 7.62mm)
• Number Of Channels: 1 Channel
• On Resistance (max): 1050 Ohms
• Propagation Delay Time: 60 ns
• On Time (max): 720 ns
• Off Time (max): 450 ns
• Supply Voltage (max): 20 V
• Supply Voltage (min): 3 V
• Maximum Power Dissipation: 200 mW
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 55 C
• Mounting Style: Through Hole
• Number Of Switches: Single
• Capacitance, Input: 5 pF (Typ.) @ 25 °C
• Circuit Type: Monolithic Integrated
• Current, Input: ± 10 mA
• Current, Input, Leakage: ± 1 μA (Max.)
• Current, Supply: 3000 μA
• Function Type: 8-Channels
• Logic Function: Multiplexer/Demultiplexer
• Logic Type: MOS
• Number Of Circuits: Single
• Package Type: DIP-16
• Power Dissipation: 500 mW @ 65 °C
• Temperature, Operating, Maximum: 125 °C
• Temperature, Operating, Minimum: -55 °C
• Temperature, Operating, Range: -55 to +125 °C
• Time, Delay, Propagation: 30 ns (Typ.)
• Voltage, Supply: 3 to 20 V
• Low In.onin. Resistance: 125W (Typ.) over 15V p.p signal-input range for VDD - VEE == 15V
• High In.offin. Resistance: channel leakage +⁄- 100pA (Typ.) at VDD - VEE == 18V
• High Degree Of Linearity: 0.5%
• Package: 16PDIP
• Maximum On Resistance: 1050@5V Ohm
• Maximum Propagation Delay Bus To Bus: 20@15V|30@10V|60@5V ns
• Multiplexer Architecture: 8:1
• Maximum Turn-off Time: 450@5V ns
• Maximum Turn-on Time: 720@5V ns
• Power Supply Type: Single
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-1361-5

HCF4051B
TYPICAL BIAS VOLTAGES
The ADDRESS (digtal-control inputs) and INHIBIT logic levels are : "0"=V
from V
SPECIAL CONSIDERATIONS
Control of analog signals up to 20V peak to peak
can be achieved by digital signal amplitudes of 4.5
to 20V (if V
can be controlled; for V
above 13V, a V
required. For example, if V
V
can be controlled by digital inputs of 0 to 4.5V. In
TEST CIRCUIT
C
R
R
6/10
L
L
T
EE
= 50pF or equivalent (includes jig and probe capacitance)
= 200K
= Z
= -13.5, analog signals from -13.5V to 4.5V
EE
OUT
to V
of pulse generator (typically 50 )
DD
DD
- V
SS
DD
= 3V, a V
- V
DD
SS
- V
DD
DD
of at least 4.5V is
EE
= +5, V
- V
level differences
EE
of up to 13V
SS
= 0, and
certain applications, the external load resistor
current may include both V
components. To avoid drawing V
switch current flows into the transmission gate
inputs, the voltage drop across the bidirectional
switch must not exceed 0,8V (calculated from R
values shown in DC SPECIFICATIONS). No V
current will flow through R
flows into lead 3.
SS
and "1"=V
DD
. The analog signal (through the TG) may swing
L
if the switch current
DD
DD
and signal-line
current when
ON
DD