NCN6004AFTBR2G ON Semiconductor, NCN6004AFTBR2G Datasheet - Page 9

• Manufacturer Part Number: NCN6004AFTBR2G
• Description: IC INTERFACE SAM/SIM DUAL 48TQFP
• Manufacturer: ON Semiconductor

Specifications of NCN6004AFTBR2G

• Applications: PC's, PDA's
• Interface: Microcontroller
• Voltage - Supply: 1.8 V ~ 5.5 V
• Package / Case: 48-TFQFP Exposed Pad
• Mounting Type: Surface Mount
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: NCN6004AFTBR2GOS; NCN6004AFTBR2GOS; NCN6004AFTBR2GOSTR

Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
2. Maximum Electrical Ratings are defined as those values beyond which damage(s) to the device may occur at T
3. Human Body Model, R = 1500 W, C = 100 pF.
4. Absolute Maximum Rating beyond which damage(s) to the device may occur.
PIN DESCRIPTION (continued)
MAXIMUM RATINGS
Power Supply Input Supply Voltage
V
Power Supply Input Current
Digital Input Pins
Digital Output Pins
Card Interface Pins
ESD Capability, Human Body Model (Note 3)
TQFP48
Operating Ambient Temperature Range
Operating Junction Temperature Range
Maximum Junction Temperature (Note 4)
Storage Temperature Range
Pin
47
48
in
ANLG_GND
Standard Pins
Card Interface Pins (Card A or B)
Power Dissipation @ Tab = +85°C
Thermal Resistance Junction−to−Air
Symbol
INT
Rating
(Note 2)
GROUND
OUTPUT
Type
This pin is activated LOW when a card has been inserted and detected in either of the
external ports. The signal is reset by either a positive going transition on pin CS, or by a
High level on pin PWR_ON combined with CS = Low.
Similarly, an interrupt is generated when either one of the CRD_VCC output is overloaded.
On the other hand, the pin is forced to a logic High when the input voltage V
below 2.0 V min.
The associated pull up resistor is either connected to V
disconnected when EN_RPU = Low.
This pin is the ground reference for both analog and digital signals and must be
connected to the system Ground. Care must be observed to provide a copper PCB layout
designed to avoid small signals and power transients sharing the same track. Good high
frequency techniques are strongly recommended.
http://onsemi.com
Digital Input Pins
NCN6004A
Symbol
T
V
V
IV
R
V
I
V
Tag
I
Jmax
V
card
P
T
T
card
ESD
In
out
JqA
CC
out
CC
9
in
A
D
J
−0.5V < V
Description
−0.5 V < V
−0.5 < V
15 mA (internally limited)
−0.5 < V
card
−40 to +125
−65 to +150
but < 6.0 V
−40 to +85
CC
CC
Value
< CRD_VCC +0.5V
+150
in
"10
" 5
500
800
50
< V
6
or V
2
8
or V
CC
CC
CC
CC
(EN_RPU = H) or
+0.5 V,
< 5.5
< 5.5
A
= +25°C.
CC
drops
°C/W
Unit
mW
mA
mA
mA
mA
kV
kV
°C
°C
°C
°C
V
V
V
V
V