ADM1024ARUZ ON Semiconductor, ADM1024ARUZ Datasheet - Page 5

• Manufacturer Part Number: ADM1024ARUZ
• Description: IC MONITOR SYS TEMP/VOLT 24TSSOP
• Manufacturer: ON Semiconductor

Specifications of ADM1024ARUZ

• Applications: PC's, PDA's
• Interface: Serial
• Voltage - Supply: 2.8 V ~ 5.5 V
• Package / Case: 24-TSSOP
• Mounting Type: Surface Mount
• Temperature Sensor Function: Temp Sensor
• Output Type: Digital
• Package Type: TSSOP
• Operating Temperature (min): 0C
• Operating Temperature (max): 100C
• Operating Temperature Classification: Commercial
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 5.5V
• Full Temp Accuracy: +/- 2 C , +/- 3 C
• Digital Output - Bus Interface: SMBus
• Digital Output - Number Of Bits: 10 bit
• Supply Voltage (max): 12 V
• Supply Voltage (min): 2.5 V
• Maximum Operating Temperature: + 100 C
• Minimum Operating Temperature: 0 C
• Supply Current: 1.4 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

1. All voltages are measured with respect to GND, unless otherwise specified.
2. Typicals are at T
3. TUE (Total Unadjusted Error) includes Offset, Gain, and Linearity errors of the ADC, multiplexer, and on−chip input attenuators, including
4. Total monitoring cycle time is nominally m × 755 ms + n × 33244 ms, where m is the number of channels configured as analog inputs, plus 2
5. The total fan count is based on two pulses per revolution of the fan tachometer output.
6. Open−drain digital outputs may have an external pullup resistor connected to a voltage lower or higher than V
7. All logic inputs except ADD are tolerant of 5.0 V logic levels, even if V
8. Timing specifications are tested at logic levels of V
ELECTRICAL CHARACTERISTICS
OPEN−DRAIN SERIAL DATABUS OUTPUT (SDA)
SERIAL BUS DIGITAL INPUTS (SCL, SDA)
DIGITAL INPUT LOGIC LEVELS (ADD, CI, RESET, VID0−VID4, FAN1, FAN2) (Note 7)
NTEST_IN
DIGITAL INPUT CURRENT
SERIAL BUS TIMING (Note 8)
Output Low Voltage, V
High Level Output Leakage Current, I
Input High Voltage, V
Input Low Voltage, V
Hysteresis
Glitch Immunity
Input High Voltage, V
Input Low Voltage, V
Input High Current, I
Input High Current, I
Input Low Current, I
Input Capacitance, C
Clock Frequency, f
Glitch Immunity, t
Bus Free Time, t
Start Setup Time, t
Start Hold Time, t
SCL Low Time, t
SCL High Time, t
SCL, SDA Rise Time, t
SCL, SDA Fall Time, t
Data Setup Time, t
Data Hold Time, t
an external series input protection resistor value between 0 kW and 1 kW.
for the internal V
channels (D1 and D2).
to V
SDA
SCL
CC
, GND, or left open−circuit.
P
t
BUF
BUF
LOW
HIGH
SW
S
HD; STA
HD; DAT
A
CC
SCLK
SU; STA
SU; DAT
Parameter
= 25°C and represent the most likely parametric norm. Shutdown current typ is measured with V
IL
IH
IH
IL
IL
IH
IH
IN
measurement and internal temperature sensor, and n is the number of channels configured as external temperature
t
f
HD:STA
OL
r
t
LOW
t
HD:DAT
t
R
OH
T
A
= T
Figure 2. Serial Bus Timing Diagram
MIN
to T
IL
t
HIGH
= 0.8 V for a falling edge and V
I
V
V
V
V
V
V
See Figure 2
See Figure 2
See Figure 2
See Figure 2
See Figure 2
See Figure 2
See Figure 2
See Figure 2
See Figure 2
See Figure 2
See Figure 2
OUT
MAX
OUT
CC
CC
CC
IN
IN
t
http://onsemi.com
F
= V
= 0
= 2.85 V − 5.5 V
= 2.85 V − 5.5 V
= 2.85 V − 5.5 V
= −3.0 mA, V
, V
Test Conditions/Comments
= V
CC
CC
CC
= V
t
SU:DAT
5
CC
MIN
is less than 5.0 V. ADD is a three−state input that may be connected
CC
to V
= 2.85 V −3.60 V
MAX
S
, unless otherwise noted. (Note 1 and 2)
IH
t
SU:STA
= 2.2 V for a rising edge.
t
HD:STA
–1.0
Min
600
600
100
2.2
2.2
2.2
1.3
1.3
0.6
CC
(up to 6.5 V absolute maximum).
Typ
500
100
0.1
20
t
SU:STO
CC
= 3.3V.
Max
100
400
300
300
900
0.4
0.8
0.8
1.0
50
P
Unit
kHz
mV
mA
mA
mA
pF
ns
ns
ms
ns
ns
ms
ms
ns
ms
ns
ns
V
V
V
V
V
V