ATTINY12-8SU Atmel, ATTINY12-8SU Datasheet - Page 32

• Manufacturer Part Number: ATTINY12-8SU
• Description: Microcontrollers (MCU) AVR 1K FLASH 64B EE 5V 8MHZ
• Manufacturer: Atmel

Specifications of ATTINY12-8SU

• Processor Series: ATTINY1x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 1 KB
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 6
• Number Of Timers: 1
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: SOIC
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500
• Minimum Operating Temperature: - 40 C
• Cpu Family: ATtiny
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 8MHz
• Interface Type: SPI
• # I/os (max): 6
• Number Of Timers - General Purpose: 1
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Package Type: SOIC EIAJ
• Lead Free Status / Rohs Status: Details

Pin Change Interrupt
Register Description
MCU Control Register –
MCUCR
32
ATtiny11/12
The pin change interrupt is triggered by any change on any input or I/O pin. Change on
pins PB2..0 will always cause an interrupt. Change on pins PB5..3 will cause an inter-
rupt if the pin is configured as input or I/O, as described in the section “Pin Descriptions”
on page 5. Observe that, if enabled, the interrupt will trigger even if the changing pin is
configured as an output. This feature provides a way of generating a software interrupt.
Also observe that the pin change interrupt will trigger even if the pin activity triggers
another interrupt, for example, the external interrupt. This implies that one external
event might cause several interrupts.
The MCU Control Register contains control bits for general MCU functions.
Note:
• Bit 7 - Res: Reserved Bit
This bit is a reserved bit in the ATtiny11/12 and always reads as zero.
• Bit 6 - Res: Reserved Bit in ATtiny11
This bit is a reserved bit in the ATtiny11 and always reads as zero.
• Bit 6 - PUD: Pull-up Disable in ATtiny12
Setting this bit, disables all pull-ups on port B. If this bit is cleared, the pull-ups can be
individually enabled as described in section “I/O Port B” on page 36.
• Bit 5 - SE: Sleep Enable
The SE bit must be set (one) to make the MCU enter the Sleep Mode when the SLEEP
instruction is executed. To avoid the MCU entering the Sleep Mode unless it is the pro-
grammer’s purpose, it is recommended to set the Sleep Enable SE bit just before the
execution of the SLEEP instruction.
• Bit 4 - SM: Sleep Mode
This bit selects between the two available sleep modes. When SM is cleared (zero), Idle
Mode is selected as Sleep Mode. When SM is set (one), Power-down Mode is selected
as Sleep Mode. For details, refer to the paragraph “Sleep Modes” below.
• Bits 3, 2 - Res: Reserved Bits
These bits are reserved bits in the ATtiny11/12 and always read as zero.
Bit
$35
Read/Write
Initial Value
The values on the pins are sampled before detecting edges. If pin change interrupt
is enabled, pulses that last longer than one CPU clock period will generate an
interrupt. Shorter pulses are not guaranteed to generate an interrupt.
The Pull-up Disable (PUD) bit is only available in ATtiny12.
R
7
0
-
(PUD)
R(/W)
6
0
R/W
SE
5
0
R/W
SM
4
0
R
3
0
-
R
2
0
-
ISC01
R/W
1
0
ISC00
R/W
0
0
1006F–AVR–06/07
MCUCR