DC1575A Linear Technology, DC1575A Datasheet
DC1575A
Specifications of DC1575A
Related parts for DC1575A
DC1575A Summary of contents
Page 1
... MP3/MP4 Players n Digital Cameras L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and ThinSOT, PowerPath and Hot Swap are trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. TYPICAL APPLICATION Protection from Overvoltage and Overcurrent ...
Page 2
LTC4362-1/LTC4362-2 ABSOLUTE MAXIMUM RATINGS (Notes 1 and 2) Bias Supply Voltage IN to OUT (Note 3) ................................. –0.3V to 28V Input Voltages SENSE to OUT (Notes 3 and 4) .............. –0.3V to 28V ON ........................................................... –0. Output Voltages ...
Page 3
ELECTRICAL CHARACTERISTICS temperature range, otherwise specifi cations are at T SYMBOL PARAMETER Supplies V Input Voltage Range IN V Input Undervoltage Lockout IN(UVL) I Input Supply Current IN Thresholds V IN Pin Overvoltage Threshold IN(OV) ΔV Overvoltage Hysteresis OV Input ...
Page 4
LTC4362-1/LTC4362-2 TYPICAL PERFORMANCE CHARACTERISTICS Specifi cations are 25° 5V Input Supply Current vs Input Voltage 1000 100 (V) ...
Page 5
TYPICAL PERFORMANCE CHARACTERISTICS Specifi cations are 25° 5V Normal Start-Up Sequence V IN 5V/DIV V OUT 5V/DIV I CABLE 0.5A/DIV 436212 G10 20ms/DIV FIGURE 4 CIRCUIT R = 150mΩ 0.7μH ...
Page 6
LTC4362-1/LTC4362-2 BLOCK DIAGRAM IN GATEP 200k ON + – 1V 5μA OPERATION Mobile devices like cell phones and MP3/MP4 players have highly integrated subsystems fabricated from deep submicron CMOS processes. The small form factor is accompanied by low absolute maximum ...
Page 7
OPERATION If the voltage at the IN pin exceeds 5.8V (V internal N-channel MOSFET is turned off quickly to protect the load. The incoming power supply must remain below 5.7V (V – ΔV ) for the duration of the start-up ...
Page 8
LTC4362-1/LTC4362-2 APPLICATIONS INFORMATION above 1. for more than 500μs. After reset, the ON(TH) LTC4362-1 goes through the start-up cycle. In applications not requiring the overcurrent protection, tie SENSE and the exposed pad to the IN pin. PWRGD Output ...
Page 9
APPLICATIONS INFORMATION WALL ADAPTOR AC/ CABLE CABLE WALL ADAPTOR AC/ CABLE CABLE Thermal Shutdown The internal N-channel MOSFET is protected by a thermal shutdown circuit. If its temperature ...
Page 10
LTC4362-1/LTC4362-2 APPLICATIONS INFORMATION Figure 5 shows an input transient after an overcurrent. The current in L will cause V to overshoot and avalanche IN IN the internal N-channel MOSFET to C TURN-OFF V IN 10V/DIV V OUT OVERCURRENT 5V/DIV I ...
Page 11
APPLICATIONS INFORMATION C is the decoupling capacitor of the protected circuit OUT and its value is largely determined by the circuit require- ments. Using a larger C works with L OUT the dV/dt at OUT, allowing time for the LTC4362 ...
Page 12
LTC4362-1/LTC4362-2 PACKAGE DESCRIPTION 0.70 0.05 1.35 0.05 3.50 0.05 1.65 0.05 2.10 0.05 PACKAGE OUTLINE 0.25 0.05 0.45 BSC 1.35 REF RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 12 DC Package 8-Lead ...
Page 13
... Revised Overcurrent in the Applications Information section. Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa- tion that the interconnection of its circuits as described herein will not infringe on existing patent rights. ...
Page 14
... On-Resistance, Low Reverse Leakage Current, 18mV Regulated Forward Voltage (LTC4413-2 with Overvoltage Protection Sensor) www.linear.com ● V OUT 5V 0.5A C OUT 10μF D1 LN1351CTR : 3μ 2.0V to 45V 0. OUT : 3μ 1.6V to 20V 0. OUT LT 0111 REV A • PRINTED IN USA © LINEAR TECHNOLOGY CORPORATION 2010 436212fa ...