P89LPC936FDH-T NXP Semiconductors, P89LPC936FDH-T Datasheet - Page 52

• Manufacturer Part Number: P89LPC936FDH-T
• Description: MCU 8-Bit 89LP 80C51 CISC 16KB Flash 2.5V/3.3V 28-Pin TSSOP T/R
• Manufacturer: NXP Semiconductors

Specifications of P89LPC936FDH-T

• Package: 28TSSOP
• Device Core: 80C51
• Family Name: 89LP
• Maximum Speed: 18 MHz
• Ram Size: 768 Byte
• Program Memory Size: 16 KB
• Operating Supply Voltage: 2.5|3.3 V
• Data Bus Width: 8 Bit
• Program Memory Type: Flash
• Number Of Programmable I/os: 26
• Interface Type: I2C/SPI/UART
• On-chip Adc: 8-chx8-bit
• Operating Temperature: -40 to 85 °C
• Number Of Timers: 2

NXP Semiconductors
9. A/D converter
P89LPC933_934_935_936
Product data sheet
8.28.10 Hardware activation of the boot loader
8.29 User configuration bytes
8.30 User sector security bytes
9.1 General description
9.2 Features and benefits
The boot loader can also be executed by forcing the device into ISP mode during a
power-on sequence (see the P89LPC933/934/935/936 User manual for specific
information). This has the same effect as having a non-zero status byte. This allows an
application to be built that will normally execute user code but can be manually forced into
ISP operation. If the factory default setting for the boot vector is changed, it will no longer
point to the factory preprogrammed ISP boot loader code. After programming the flash,
the status byte should be programmed to zero in order to allow execution of the user’s
application code beginning at address 0000H.
Some user-configurable features of the P89LPC933/934/935/936 must be defined at
power-up and therefore cannot be set by the program after start of execution. These
features are configured through the use of the flash byte UCFG1. Please see the
P89LPC933/934/935/936 User manual for additional details.
There are eight User Sector Security Bytes on the P89LPC933/934/935/936 device. Each
byte corresponds to one sector. Please see the P89LPC933/934/935/936 User manual for
additional details.
The P89LPC935/936 have two 8-bit, 4-channel multiplexed successive approximation
analog-to-digital converter modules sharing common control logic. The P89LPC933/934
have a single 8-bit, 4-channel multiplexed analog-to-digital converter and an additional
DAC module. A block diagram of the A/D converter is shown in
consists of a 4-input multiplexer which feeds a sample-and-hold circuit providing an input
signal to one of two comparator inputs. The control logic in combination with the SAR
drives a digital-to-analog converter which provides the other input to the comparator. The
output of the comparator is fed to the SAR.
Two (P89LPC935/936) 8-bit, 4-channel multiplexed input, successive approximation
A/D converters with common control logic (one A/D on the P89LPC933/934).
Four result registers for each A/D.
Six operating modes:
Four conversion start modes:
Fixed channel, single conversion mode.
Fixed channel, continuous conversion mode.
Auto scan, single conversion mode.
Auto scan, continuous conversion mode.
Dual channel, continuous conversion mode.
Single step mode.
Timer triggered start.
All information provided in this document is subject to legal disclaimers.
Rev. 8 — 12 January 2011
8-bit microcontroller with accelerated two-clock 80C51 core
P89LPC933/934/935/936
Figure
23. Each A/D
© NXP B.V. 2011. All rights reserved.
52 of 77