PIC16C74B-20/P Microchip Technology Inc., PIC16C74B-20/P Datasheet - Page 61

• Manufacturer Part Number: PIC16C74B-20/P
• Description: 40 PIN, 7 KB OTP, 192 RAM, 33 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16C74B-20/P

• A/d Inputs: 8-Channel, 8-Bit
• Cpu Speed: 5 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 33
• Interface: I2C/SPI/USART
• Memory Type: OTP
• Number Of Bits: 8
• Package Type: 40-pin PDIP
• Programmable Memory: 7K Bytes
• Ram Size: 192 Bytes
• Speed: 4 MHz
• Timers: 2-8-bit, 1-16-bit
• Voltage, Range: 2.5-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

10.3.1.1
Once the SSP module has been enabled, it waits for a
START condition to occur. Following the START condi-
tion, 8-bits are shifted into the SSPSR register. All
incoming bits are sampled with the rising edge of the
clock (SCL) line. The value of register SSPSR<7:1> is
compared to the value of the SSPADD register. The
address is compared on the falling edge of the eighth
clock (SCL) pulse. If the addresses match, and the BF
and SSPOV bits are clear, the following events occur:
a)
b)
c)
d)
In 10-bit address mode, two address bytes need to be
received by the slave (Figure 10-7). The five Most Sig-
nificant bits (MSbs) of the first address byte specify if
this is a 10-bit address. Bit R/W (SSPSTAT<2>) must
specify a write so the slave device will receive the sec-
ond address byte. For a 10-bit address, the first byte
would equal ‘1111 0 A9 A8 0’, where A9 and A8 are
the two MSbs of the address. The sequence of events
for 10-bit address is as follows, with steps 7 - 9 for
slave-transmitter:
TABLE 10-2:
Note:
2000 Microchip Technology Inc.
Transfer is Received
Status Bits as Data
The SSPSR register value is loaded into the
SSPBUF register.
The buffer full bit, BF is set.
An ACK pulse is generated.
SSP interrupt flag bit, SSPIF (PIR1<3>) is set
(interrupt is generated if enabled) - on the falling
edge of the ninth SCL pulse.
BF
0
1
1
0
Shaded cells show the conditions where the user software did not properly clear the overflow condition.
Addressing
SSPOV
DATA TRANSFER RECEIVED BYTE ACTIONS
0
0
1
1
SSPSR
Yes
No
No
No
SSPBUF
PIC16C63A/65B/73B/74B
1.
2.
3.
4.
5.
6.
7.
8.
9.
Generate ACK
Receive first (high) byte of address (bits SSPIF,
BF, and bit UA (SSPSTAT<1>) are set).
Update the SSPADD register with second (low)
byte of Address (clears bit UA and releases the
SCL line).
Read the SSPBUF register (clears bit BF) and
clear flag bit SSPIF.
Receive second (low) byte of address (bits
SSPIF, BF, and UA are set).
Update the SSPADD register with the first (high)
byte of address, if match releases SCL line, this
will clear bit UA.
Read the SSPBUF register (clears bit BF) and
clear flag bit SSPIF.
Receive Repeated START condition.
Receive first (high) byte of address (bits SSPIF
and BF are set).
Read the SSPBUF register (clears bit BF) and
clear flag bit SSPIF.
Pulse
Yes
No
No
No
(SSP Interrupt occurs
Yes, SSPOV is set
Set bit SSPIF
if enabled)
Yes
Yes
Yes
DS30605C-page 61