PIC16C711-04/P Microchip Technology Inc., PIC16C711-04/P Datasheet - Page 19

• Manufacturer Part Number: PIC16C711-04/P
• Description: 18 PIN, 1.75 KB OTP, 68 RAM, 13 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16C711-04/P

• A/d Inputs: 4-Channel, 8-Bit
• Cpu Speed: 5 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 13
• Memory Type: OTP
• Number Of Bits: 8
• Package Type: 18-pin PDIP
• Programmable Memory: 1.75K Bytes
• Ram Size: 68 Bytes
• Speed: 20 MHz
• Timers: 1-8-bit
• Voltage, Range: 2.5-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

4.2.2.3
The INTCON Register is a readable and writable regis-
ter which contains various enable and flag bits for the
TMR0 register overflow, RB Port change and External
RB0/INT pin interrupts.
FIGURE 4-9:
Applicable Devices
1997 Microchip Technology Inc.
bit7
bit 7:
bit 6:
bit 5:
bit 4:
bit 3:
bit 2:
bit 1:
bit 0:
Note 1: For the PIC16C71, if an interrupt occurs while the GIE bit is being cleared, the GIE bit may be uninten-
R/W-0
GIE
Interrupt flag bits get set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the
global enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to
enabling an interrupt.
INTCON REGISTER
GIE:
1 = Enables all un-masked interrupts
0 = Disables all interrupts
ADIE: A/D Converter Interrupt Enable bit
1 = Enables A/D interrupt
0 = Disables A/D interrupt
T0IE: TMR0 Overflow Interrupt Enable bit
1 = Enables the TMR0 interrupt
0 = Disables the TMR0 interrupt
INTE: RB0/INT External Interrupt Enable bit
1 = Enables the RB0/INT external interrupt
0 = Disables the RB0/INT external interrupt
RBIE: RB Port Change Interrupt Enable bit
1 = Enables the RB port change interrupt
0 = Disables the RB port change interrupt
T0IF: TMR0 Overflow Interrupt Flag bit
1 = TMR0 register has overflowed (must be cleared in software)
0 = TMR0 register did not overflow
INTF: RB0/INT External Interrupt Flag bit
1 = The RB0/INT external interrupt occurred (must be cleared in software)
0 = The RB0/INT external interrupt did not occur
RBIF: RB Port Change Interrupt Flag bit
1 = At least one of the RB7:RB4 pins changed state (must be cleared in software)
0 = None of the RB7:RB4 pins have changed state
tionally re-enabled by the RETFIE instruction in the user’s Interrupt Service Routine. Refer to Section 8.5
for a detailed description.
R/W-0
ADIE
(1)
INTCON REGISTER (ADDRESS 0Bh, 8Bh)
Global Interrupt Enable bit
R/W-0
T0IE
710 71 711 715
R/W-0
INTE
R/W-0
RBIE
R/W-0
T0IF
R/W-0
INTF
Note:
Interrupt flag bits get set when an interrupt
condition occurs regardless of the state of
its corresponding enable bit or the global
enable bit, GIE (INTCON<7>).
R/W-x
RBIF
bit0
R = Readable bit
W = Writable bit
U = Unimplemented bit,
- n = Value at POR reset
PIC16C71X
read as ‘0’
DS30272A-page 19