MSO-0008P-012 NCC, MSO-0008P-012 Datasheet - Page 22

• Manufacturer Part Number: MSO-0008P-012
• Description: Socket, Relay; 8 Pin Octal
• Manufacturer: NCC
• Type: Octalr

Specifications of MSO-0008P-012

• Number Of Contacts: 8
• Time Range: 0.05 Sec. to 999 Min.
• Output Rating: 10 A @ 240 VAC Max.; 100 mA @ 5 VDC Min.
• Operating Temperature: –23°C to +55°C

AMETEK National Controls Corp. • 1725 Western Drive • West Chicago, Illinois 60185 • Tel: [phone] • 630-231-5900 • FAX: [phone] • www.nationalcontrols.com
1-12
Delay On Make
K1 Series
FEATURES
●
●
●
●
●
●
●
●
●
●
●
Operating Logic: Upon application of volt-
age to the input terminals, the time delay
cycle starts. At the end of the preset time
delay, the relay coil is energized and the
contacts transfer. Reset is accomplished by
the removal of input voltage.
Note: 1) Remote potentiometer leads should be shielded when
running close to other wires; 2) The minimum time setting on
external resistor-adjustable time delay relays is obtained by short-
ing together the external resistor terminals of the relay; 3) The
maximum time setting within tolerance limits is obtained by using
a 1 megohm resistor; 4) Timing values between the minimum
and maximum limits are linear with resistance within 10%; 5)
Recommend 1/4 W minimum resistor be used.
LOGIC FUNCTION DIAGRAM
ORDERING INFORMATION
Optional Potentiometer: Part Number ASY-0001M-450
Input
Voltage
Relay
Coil
100% functionally tested
No false contact transfer when reset
during timing
Digital timing circuit
Time delays to 5 minutes
Low cost
Compact size
Spade type base
Wide operating temperature range
Fiberglass reinforced circuit board
Polycarbonate, 94V-2 housing material
3 to 300 sec.
3 to 300 sec.
TIME RANGE
.1 to 10 sec.
.3 to 30 sec.
.6 to 60 sec.
TIME RANGE
.1 to 10 sec.
.3 to 30 sec.
.6 to 60 sec.
.1 to 5 sec.
On
Off
On
Off
TIME DELAY RELAYS
Delay On Make Function
File #E59090
Timing
K1K-00010-666
K1K-00030-666
K1K-00060-666
K1K-00300-666
K1K-00010-667
K1K-00300-667
KNOB ADJST
KNOB ADJST
12 VDC
CASE 6
CASE 6
24 VAC
—
—
—
K1K-00010-566
K1K-00030-566
K1K-00060-566
K1K-00010-567
REMOTE POT
REMOTE POT
12 VDC
CASE 5
CASE 5
24 VAC
—
—
—
—
—
SPECIFICATIONS
TIME DELAY
Adjustment: Knob or external resistor, factory
fixed on special order (min. order required)
Range: 100 ms to 5 minutes in 5 ranges
Repeatability: ±.5% at constant temperature and
reset time, but not less than 16 ms.
Accuracy: Maximum time +(10%, +20 ms)/-0%;
Minimum time -50%/+(0%, +20 ms)
Reset Time: 80 ms max.
INPUT
Operating Voltage: 24, 120 VAC; 12, 24 VDC
±10% (DC models have reverse polarity protec-
tion. Unfiltered input voltage to them must be full-
wave rectified)
Power Consumption: 3 VA max.
Frequency: 50/60 Hz (AC units)
OUTPUT
Type: Relay contacts, DPDT (2 form C)
Rating: 10 A max. resistive at 240 VAC; 100 mA
at 5 VDC min. load current
Life:
Mechanical: 1,000,000 operations
Full Load: 150,000 operations
PROTECTION
Transient Voltage: 12 and 24 V timers are pro-
tected by a 1 joule metal oxide varistor; 120 V
and 240 V timers are protected by a 5 joule metal
oxide varistor.
Dielectric Breakdown: 1500 VAC, RMS min. at
60 Hz between input and outputs and between
outputs
MECHANICAL
Termination: Spade (.187” x .020” terminal) type
plug-in base
Mounting: Socket mount, part number
MSO-00KUP-012, or flange mount
ENVIRONMENTAL
Storage Temperature: -23°C to 70°C
Operating Temperature: -23°C to 55°C
K1K-00010-662
K1K-00060-662
K1K-00300-662
K1K-00010-661
K1K-00030-661
K1K-00060-661
K1K-00300-661
KNOB ADJST
KNOB ADJST
120 VAC
24 VDC
CASE 6
CASE 6
—
—
K1K-00005-761
K1K-00030-761
K1F-00060-562
REMOTE POT
REMOTE POT
120 VAC
24 VDC
CASE 5
CASE 7
—
—
—
—
—
—
K1F-00010-561
K1F-00060-561
REMOTE POT
120 VAC
CASE 5
—
—
—
Consult factory for any special requirements not
listed in catalog (minimum order requirement may
apply).
(3021-3)
.70
Max.
A
4
A
1
4
7
1
7
Polarity Shown is
Polarity Shown is
Timing Resistor
for D.C. Models
Case 7
Case 5
for D.C. Models
(By Cust.)
Voltage
Case 6
Voltage
1.835
Input
1.531
Input
1.90
2.125
2.50
5
2
.437
.25
3
6
3
6
9
B
9
B
.25
2 Pl.
.156