MSO-0008P-012 NCC, MSO-0008P-012 Datasheet - Page 20

• Manufacturer Part Number: MSO-0008P-012
• Description: Socket, Relay; 8 Pin Octal
• Manufacturer: NCC
• Type: Octalr

Specifications of MSO-0008P-012

• Number Of Contacts: 8
• Time Range: 0.05 Sec. to 999 Min.
• Output Rating: 10 A @ 240 VAC Max.; 100 mA @ 5 VDC Min.
• Operating Temperature: –23°C to +55°C

AMETEK National Controls Corp. • 1725 Western Drive • West Chicago, Illinois 60185 • Tel: [phone] • 630-231-5900 • FAX: [phone] • www.nationalcontrols.com
1-10
Delay On Make
Q1F Alarm Series
FEATURES
●
●
●
●
●
●
●
●
●
●
The Q1F Delay to Alarm Cube Timer is
intended for use as a Delay On Make audi-
ble alarm.
Operating Logic: Upon application of the
input voltage, the time delay starts. At the
end of the preset time delay the audible
alarm is activated. Reset is accomplished
by removing input voltage.
Note: 1) Remote potentiometer leads should be shielded when
running close to other wires; 2) The minimum time setting on
external resistor-adjustable time delay relays is obtained by short-
ing together the external resistor terminals of the relay; 3) The
maximum time setting within tolerance limits is obtained by using
a 1 megohm resistor; 4) Timing values between the minimum
and maximum limits are linear with resistance within 10%; 5)
Recommend 1/4 W minimum resistor be used.
LOGIC FUNCTION DIAGRAM
Input
Voltage
ORDERING INFORMATION
Optional Potentiometer: Part Number ASY-0001M-450
Audio
Alarm
100% functionally tested
Time delays to 10 hours standard
Loud audio alarm for use in noisy envi-
ronments
Solid state digital timing
20:1 maximum to minimum timing ratio
Low cost
Compact size
Superior transient protection
Flame-retardant and solvent-resistant
polyester thermoplastic housing
On
Off
On
Off
TIME DELAY RELAYS
180 to 3600 sec.
Delay On Make Function
15 to 300 sec.
30 to 600 sec.
TIME RANGE
.05 to 1 sec.
.25 to 5 sec.
.5 to 10 sec.
3 to 60 sec.
.25 to 5 hrs.
.5 to 10 hrs.
File #E165149
Timing
(Alarm Output)
120 VAC 50/60 Hz
Q1F-00060-3A1
Q1F-03600-3A1
Q1F-18000-3A1
Q1F-36000-3A1
—
—
—
—
—
SPECIFICATIONS
TIME DELAY
Adjustment: External resistor, factory fixed on
special order (min. order requirement)
Range: 50 ms to 10 hours in 9 ranges
Repeatability: ±.5% +8 ms max. (0.25% typical)
at constant temperature
Accuracy: Max. +0%, -30% at Rt = 0 ohm
Reset Time:
During Timing: 300 ms
After Timeout: 150 ms
INPUT
Operating Voltage: 120 or 240 VAC ±10%
Frequency: 50/60 Hz
OUTPUT
Type: Solid state Piezo Audio Alarm
Alarm Frequency: 3.15 kHz ±0.5 kHz
Sound Pressure Level: 76 dB at 1 meter
Life: 10,000,000 operations
PROTECTION
Transient Voltage: Metal oxide varistor
Dielectric Breakdown: 3000 VAC, RMS, termi-
nals to mounting
Insulation Resistance: 100 megohms min.
between terminals and case
MECHANICAL
Termination: .25” x .032” male fast-on terminals
Mounting: Surface mount with one #8 screw
ENVIRONMENTAL
Storage Temperature: -40°C to 75°C
Operating Temperature: 0°C to 65°C
Humidity: 95% relative
240 VAC 50/60 Hz
Q1F-00001-3A5
Q1F-00005-3A5
Q1F-00010-3A5
Q1F-00060-3A5
Q1F-00300-3A5
Q1F-00600-3A5
Q1F-03600-3A5
Q1F-18000-3A5
Q1F-36000-3A5
External Resistance/Time Delay Relationship
1 megohm external resistance is required to obtain
the maximum time for all ranges. To determine the
actual resistance needed to obtain the required time
delay, use the following formula:
Note: Due to component tolerances, the actual time
obtained will normally be within 5% of desired time.
Consult factory for any special requirements not
listed in catalog (minimum order requirement may
apply).
Rt=
Tmaximum - Tminimum
Trequired - Tminimum
.25 X .032 MALE FAST-ON
2.00 SQ.
C L
TERMINALS (5 PL.)
Rt
L C
1.25
.88
x 1,000,000 ohms
.170
DIA.
Voltage
Input